1-20 of 220 Search Results for

torsion testing

Sort by
Image
Published: 01 January 1998
Fig. 9-29 Impact energy absorbed during torsion testing of S-type silicon tool steels subjected to various austenitizing and quenching treatments. Curves 1 to 3, Bethlehem Steel Co.; curve 4, Ref 14 Curve Composition, % Quenching temperature Quenching medium C Si Mo V °C °F More
Image
Published: 01 August 2005
Fig. 2.13 Comparison between failure criteria: correlation with tension-torsion test data of aluminum and copper. Source: Ref 2.7 (graphs adopted from Ref 2.6 ) More
Image
Published: 01 August 2005
Fig. 2.14 Comparison between failure criteria: correlation with tension-torsion test data of steels. Source: Ref 2.7 (graphs adopted from Ref 2.6 ) More
Image
Published: 01 November 2012
Fig. 22 Schematic of torsion test. Reprinted with the permission of Cambridge University Press. Source: Ref 11 More
Image
Published: 01 January 2015
Fig. 15.14 Schematic diagram of torsion-tested wire in which a primary transverse shear fracture and a spiral delamination fracture (labeled “secondary fracture”) have developed. Source: Ref 15.48 More
Image
Published: 01 December 2006
Fig. 7.120 Time-dependent wear rates from hot torsion tests for the hot working steel 1.2779 as the rotating steel heated to 550 °C and the extruded materials AlMgSi0.5, CuZn42 and CuNi30 heated to the deformation temperature [ Schi 82 ] More
Image
Published: 01 January 1998
Fig. 8-33 Static torsion tests on quenched and quenched-and-tempered L6 steel containing 0.70% C, 0.55% Mn, 0.85% Cr, 1.40% Ni, and 0.25% Mo. Data from Teledyne VASCO More
Image
Published: 01 January 1998
Fig. 10-11 Results of static torsion tests of O1 tool steel containing 1.2% Mn as a function of tempering temperature. The hardness before testing is noted along the abscissa. Data from Teledyne VASCO More
Image
Published: 01 January 1998
Fig. 10-12 Results of static torsion tests of type O7 tool steel containing 1.6% W as a function of tempering temperature. The hardness before testing is noted along the abscissa. Data from Teledyne VASCO More
Image
Published: 01 January 1998
Fig. 12-15 Comparison of ductility in static torsion tests of D3 (left) and D2 (right) tool steels quenched to maximum hardness and tempered at the three temperatures shown. Data from Teledyne VASCO More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 February 2005
DOI: 10.31399/asm.tb.chffa.t51040025
EISBN: 978-1-62708-300-3
... Abstract This chapter explains how to determine flow stress and forgeability using data from tensile tests, compression tests, ring tests, and torsion tests. It describes sample preparation, tooling and equipment, test procedures, error sources, and data plotting techniques. It also provides...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610025
EISBN: 978-1-62708-303-4
.... The chapter also covers compression, shear, and torsion testing, the prediction of yielding, residual stress, and hardness. compression hardness notched tensile test shear stress-strain curve tension MANY MATERIALS, both during initial fabrication and later when placed in service...
Image
Published: 01 December 2006
Fig. 4.47 Hot low curves for CuZn8 obtained from different methods. (a) Hot-tensile tests. (b) Torsion tests [ Bau 63 , DGM 78 ] More
Image
Published: 01 December 2006
Fig. 5.63 Flow stress and workability of steels measured from the number of turns to failure in torsion tests as a function of temperature. (a) Flow stress. (b)δ. (c) Deformation capacity [ Ben 73 ] More
Image
Published: 01 December 2006
Fig. 5.13 Flow stress of some non-age-hardening aluminum alloys as a function of the deformation temperature (maximum of the flow curve in torsion tests with φ ˙ g = 0.655 ⁢     s − 1 [ Ake 70 ] More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.spsp2.t54410315
EISBN: 978-1-62708-265-5
... and transverse orientation of shear stresses that develop in a torsion-tested wire ( Ref 15.47 . In wires with fine, uniformly deformed pearlitic microstructures and good surface condition, after a significant number of applied torsional twists, smooth, flat shear fractures develop on transverse wire surfaces...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270124
EISBN: 978-1-62708-301-0
... that a considerable amount of rubbing occurred after the shaft broke. SEM fractography revealed deformation marks and elongated dimples, typical of shear overloads, along with other details. Based on their analysis, investigators concluded that the cardan shaft failed under torsional overload. They also cited a need...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 1998
DOI: 10.31399/asm.tb.ts5.t65900181
EISBN: 978-1-62708-358-4
.... AQ, as quenched. Source: Ref 4 Fig. 10-11 Results of static torsion tests of O1 tool steel containing 1.2% Mn as a function of tempering temperature. The hardness before testing is noted along the abscissa. Data from Teledyne VASCO Fig. 10-12 Results of static torsion tests...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 1998
DOI: 10.31399/asm.tb.ts5.t65900165
EISBN: 978-1-62708-358-4
... martensite embrittlement range. Fig. 9-10 Impact energy absorbed as a function of tempering temperature during unnotched Charpy and torsion impact testing of S1 steel specimens. Data from Bethlehem Steel Co. Curve Test Composition, % Quenching temperature Quenching medium C Si W Cr V...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270122
EISBN: 978-1-62708-301-0
... microscopes, was flat and shiny with deformation marks and dimples, typical of torsional overload, and signs of severe rubbing on the periphery. Based on their observations, investigators concluded that the quill shaft failed by torsional overload, the source of which could not be determined. quill...