1-20 of 629 Search Results for

tolerance

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610303
EISBN: 978-1-62708-303-4
... control plans optimized for different circumstances, examines the damage tolerance requirements used by different industries, and discusses various approaches for fatigue design. damage tolerance analysis fracture control proof testing FRACTURE CONTROL is the concerted effort to ensure safe...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540215
EISBN: 978-1-62708-309-6
... Abstract This chapter presents a fracture-mechanics-based approach to damage tolerance, accounting for mechanical, metallurgical, and environmental factors that drive crack development and growth. It begins with a review of stress-intensity factors corresponding to a wide range of crack...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1995
DOI: 10.31399/asm.tb.sch6.t68200206
EISBN: 978-1-62708-354-6
... Abstract Users of steel castings establish performance requirements for specific characteristics of the castings based on the planned use. They express tolerance for variation in those characteristics to the producer of the castings. One issue which should never be taken for granted...
Image
Published: 31 March 2024
Fig. 1.19 Typical tooth profile tolerance charts More
Image
Published: 31 March 2024
Fig. 1.27 Lead tolerances for crowned teeth. (a) Crown tolerance only. (b) Total tolerance band crown lead More
Image
Published: 01 October 2011
Fig. 6.4 Approximate values of surface roughness and tolerance on dimensions typically obtained with different manufacturing processes. Polymers are different from metals and ceramics in that they can be processed to a very high surface smoothness, but tight tolerances are seldom possible More
Image
Published: 01 December 2009
Fig. 10.2 ±1% resistors. After sorting, the distribution at this tight tolerance appears to be nearly uniform. More
Image
Published: 01 December 2009
Fig. 15.1 Tolerance analysis and x-ray images. A mechanism designer and manufacturer experienced pin jamming in one of its products. A fault-tree analysis hypothesized the existence of an interference fit. The tolerance analysis drawing on the left showed that this could occur under certain More
Image
Published: 01 June 2016
Fig. 1.12 Early cold spray repair of a Sandia satellite housing. Out-of-tolerance surface was built up with cold spray and then remachined to meet specifications. This is believed to be the first cold-sprayed part to be launched into space. Courtesy of Sandia National Laboratories More
Image
Published: 01 December 2015
Fig. 2 Stress-corrosion cracking (SCC) defect tolerance parameter ( K ISCC /σ y ), where K ISCC is the threshold SCC intensity factor and σ y is yield stress versus hardness for carbon steel weldments in three environments. Data are derived from published tests on precracked specimens More
Image
Published: 01 December 2015
Fig. 12 The H 2 S-pH tolerance of low-carbon martensitic stainless steel tested by the slow strain-rate technique. HAC, hydrogen-assisted cracking. Source: Ref 25 More
Image
Published: 01 July 2009
Fig. 20.16 Forgeability tolerance found by compressing solid cylinders of high-strength beryllium at various temperatures to various reductions in height. The compression yield strength of samples taken from the resulting forgings is listed near each data point in units of MPa. Source: Floyd More
Image
Published: 01 February 2005
Fig. 1.2 Surface finish and tolerance range for various manufacturing processes. [ Schey et al., 2000 ] More
Image
Published: 01 November 2012
Fig. 30 Use of stitching to improve damage tolerance. Source: Ref 16 More
Image
Published: 01 November 2013
Fig. 2 Dimensional tolerance achievable through various machining operations under general machining conditions as a function of feature size. Source: Ref 1 More
Image
Published: 01 October 2012
Fig. 12.5 Approximate values of surface roughness and tolerance on dimensions typically obtained with different manufacturing processes. ECM, electrochemical machining; EDM, electrical discharge machining. Source: Ref 12.7 More
Image
Published: 01 November 2010
Fig. 14.20 Use of stitching to improve damage tolerance. Source: Ref 18 More
Image
Published: 01 November 2010
Fig. 1.16 Compared with aluminum alloy sheet, a composite laminate has poor tolerance of stress concentration because of its brittle nature. Source: Ref 3 More
Image
Published: 01 July 1997
Fig. 26 Stress-corrosion cracking (SCC) defect tolerance parameter vs. hardness for carbon steel weldments in three environments. Data are derived from published tests on pre-cracked specimens of various types of carbon steel base metals, heat-affected zones, and weld metals. SCC defect More
Image
Published: 31 March 2024
Fig. 1.26 Allowable lead tolerances More