1-20 of 1038 Search Results for

thinning

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 November 2019
Figure 56 Force map obtained during thinning to ensure contour. Thinning continues until the force is equal. More
Image
Published: 01 November 2019
Fig. 8 Glass/epoxy on trimmed substrate prior to thinning More
Image
Published: 01 November 2019
Fig. 10 Turner method of substrate thinning More
Image
Published: 01 November 2019
Figure 15 (Left) Local thinning through laser milling or FIB provides an opportunity to get closer to an area of interest for high-resolution scanning. The SV MR sensor is shown in a cavity that is 500 µm ×500 µm and 250 µm deep. (Right) SV MR sensor on a die surface, with an illustrated More
Image
Published: 01 November 2019
Figure 28 Transmission of Si improves with wafer thinning Note that transmission for 10 20 cm −3 material through 100 microns is less than a percent. Calculated from empirical formulas given by A. Falk in [7] . More
Image
Published: 01 March 2002
Fig. 6.13 A jet thinning device for preparing thin foils. Source: South Bay Technology Corporation More
Image
Published: 01 September 2008
Fig. 8 Bent product tube with 90° bend and minimal thinning at outer tube wall of ~18% of starting tube wall thickness More
Image
Published: 01 August 2018
Fig. 6.9 Sample removal and thinning using FIB. In a sample where the microstructure was revealed by FIB sputtering/cleaning of the surface, the location of the thin sample to be removed is selected and an ion beam–assisted platinum deposition is done on location (a). A trench is dug on each More
Image
Published: 01 December 2018
Fig. 6.83 SEM micrographs showing extensive wall thinning at puncture contours surrounded by aggravated erosion damage, (a) 100×, (b) 250× More
Image
Published: 01 August 2012
Fig. 7.13 Comparison of sidewall thinning distributions obtained from the ironing tests with different lubricants (Lub); curvilinear length (C.L.). Source: Ref 7.19 More
Image
Published: 01 August 2012
Fig. 8.5 Thinning and thickening of the cup. Source: Ref 8.4 More
Image
Published: 01 August 2012
Fig. 3.1 Schematic of forming limit diagram curves and constant thinning to illustrate the choice of indicator for failure in the part during the stamping/sheet hydroforming process. Source: Ref 3.11 More
Image
Published: 01 August 2012
Fig. 3.8 Thinning distribution in the final part predicted by finite-element simulation using optimum initial blank geometry. Source: Ref 3.17 More
Image
Published: 01 August 2012
Fig. 3.12 Predicted thinning percentage along the curvilinear length for sheet hydroforming with punch process at a punch stroke = 34.3 mm (1.35 in.). Source: Ref 3.20 More
Image
Published: 01 August 2012
Fig. 4.6 Variation of punch diameter and wall thinning in progressive forming stages (part A). Source: Ref 4.6 More
Image
Published: 01 August 2012
Fig. 4.9 Location of maximum thinning at the first stage (determines the upper limit of the punch diameter for the next stage) More
Image
Published: 01 August 2012
Fig. 8.20 Thinning distribution comparison along section C-C predicted by finite-element simulation for optimum blank holder force (BHF) compared with part currently formed using constant BHF at University of Dortmund (IUL), Germany. Source: Ref 8.24 More
Image
Published: 01 August 2012
Fig. 13.10 Sheet thinning in incremental sheet metal forming. Source: Ref 13.3 More
Image
Published: 30 April 2020
Fig. 5.19 Shear-rate thinning behavior for stainless steel powder in a wax-polymer binder. These data are taken at 80 °C (175 °F) and 60 vol% solids loading, resulting in significant viscosity reduction at higher shear strain rates. Source: Khakbiz et al. ( Ref 2 ) More
Image
Published: 01 December 1999
Fig. 8.16 Effect of local case thinning by grinding on the bending fatigue strength of Ni-Cr steel gear teeth. Source: Ref 16 More