This chapter is a detailed account of the tensile testing procedure used for evaluating metals and alloys. The discussion covers the stress-strain behavior of metals determined by tensile testing, properties determined from testing, test machines for measuring mechanical properties, and general procedures of tensile testing. Three distinct aspects of standard test methods for tension testing of metallic materials are discussed: test piece preparation, geometry, and material condition; test setup and equipment; and test procedure.

This data set contains the results of uniaxial tensile tests of a wide range of aluminum casting alloys conducted at high temperatures from 100 to 370 deg C, subzero temperatures from -269 to -28 deg C, and room temperature after holding at high temperatures from 100 to 370 deg C. In most cases, tests were made of several lots of material of each alloy and temper. The results for the several lots were then analyzed together graphically and statistically, and the averages were normalized to the room-temperature typical values. For some alloys, "representative" values (raw data) rather than typical values are provided.

Tensile tests are performed for several reasons related to materials development, comparison, selection, and quality control. The properties derived from tensile tests are used in selecting materials for engineering applications. Tensile properties often are used to predict or estimate the behavior of a material under forms of loading other than uniaxial tension. This chapter provides a brief overview of tensile specimens and test machines, stress-strain curves, true stress and strain, and test methodology and data analysis.

This chapter focuses on mechanical behavior under conditions of uniaxial tension during tensile testing. It begins with a discussion of properties determined from the stress-strain curve of a metal, namely, tensile strength, yield strength, measures of ductility, modulus of elasticity, and resilience. This is followed by a section describing the parameters determined from the true stress-true strain curve. The chapter then presents the mathematical expressions for the flow curve. The chapter reviews the effect of strain rate and temperature on the stress-strain curve and describes the instability in tensile deformation and stress distribution at the neck in the tensile specimen. It discusses the processes involved in ductility measurement and notch tensile test in tensile specimens. The parameter that is commonly used to characterize the anisotropy of sheet metal is covered. Finally, the chapter covers the characterization of fractures in tensile test specimens.

This chapter discusses the methodology of the tensile test and the effect of some of the variables on the tensile properties. The methodology and variables discussed are shape of the item being tested, method of gripping the item, method of applying the force, determination of strength properties other than the maximum force required to fracture the test item, ductility properties to be determined, speed of force application or speed of elongation, and test temperature. The chapter presents the definitions of the basic terms and their units, along with discussions of basic stress-strain behavior and the differences between related terms, such as stress and force and strain and elongation. It considers the parts of a tensile test, namely, test-piece preparation, geometry, and material condition; test setup and equipment; and test procedures. The chapter provides information on post-test measurements and describes the effect of strain concentrations and strain rate on tensile properties.

This chapter reviews the current technology and examines force application systems, force measurement, strain measurement, important instrument considerations, gripping of test specimens, test diagnostics, and the use of computers for gathering and reducing data. The influence of the machine stiffness on the test results is also described, along with a general assessment of test accuracy, precision, and repeatability of modern equipment. The chapter discusses various types of testing machines and their operations. Emphasis is placed on strain-sensing equipment. The chapter briefly describes load condition factors, such as strain rate, machine rigidity, and various testing modes by load control, speed control, strain control, and strain-rate control. It provides a description of environmental chambers for testing and discusses the processes involved in the force verification of universal testing machines. Specimen geometries and standard tensile tests are also described.

This chapter introduces the basic concepts of mechanical design and its general relation with the properties derived from tensile testing. It begins with a description of the basic objective of product design. Next, a simple tie bar is used to illustrate the application of mechanical property data to material selection and design and to highlight the general implications for mechanical testing. Material subjected to the basic stress conditions is considered to establish design approaches and mechanical test methods, first in static loading and then in dynamic loading and aggressive environments. The chapter then briefly describes design criteria for some basic property combinations such as strength, weight, and costs as well as stiffness in tension. Additionally, it describes the processes involved in mechanical testing for stress at failure and elastic modulus. Finally, the chapter examines the correlation between hardness and strength.

Sheet metal forming operations consist of a large family of processes, ranging from simple bending to stamping and deep drawing of complex shapes. Because sheet forming operations are so diverse in type, extent, and rate, no single test provides an accurate indication of the formability of a material in all situations. However, as discussed in this chapter, the uniaxial tensile test is one of the most widely used tests for determining sheet metal formability. This chapter describes the effect of material properties and temperature on sheet metal formability. Information on the types of formability tests is also provided. The chapter discusses the processes involved in uniaxial and plane-strain tensile testing. Examples include the uniaxial tensile test and the plane-strain tensile test which are subsequently described.

The tensile test provides a relatively easy, inexpensive technique for developing mechanical property data for the selection, qualification, and utilization of metals and alloys in engineering service. The tensile test requires interpretation, and interpretation requires a knowledge of the factors that influence the test results. This chapter provides a metallurgical perspective for such interpretation. The topics covered include elastic behavior, anelasticity, damping, proportional limit, yield point, ultimate strength, toughness, ductility, strain hardening, and yielding and the onset of plasticity. The chapter describes the effects of grain size on yielding, effect of cold work on hardness and strength, and effects of temperature and strain-rate on the properties of metals and alloys. It provides information on true stress-strain relationships and special tests developed to measure the effects of test/specimen conditions. Finally, the chapter covers the characterization of tensile fractures of ductile metals and alloys.

The testing of plastics includes a wide variety of chemical, thermal, and mechanical tests. This chapter reviews the tensile testing of plastics, which has been standardized in ASTM D 638, "Standard Test Method for Tensile Properties of Plastics," and other comparable standards. It describes the fundamental factors that affect data from tensile tests, examines the stipulations in standardized tensile testing, and discusses the utilization of data from tensile tests.

Elastomers comprise a subclass of polymers that display the ability to stretch and recover that is typical of a rubber band. This chapter describes the properties determined by tensile testing of elastomers and the factors influencing them, namely, structuring of the molecular matrix, compounding, specimen preparation, specimen type, vulcanization parameters, and temperature. The chapter also provides information on ASTM D 412, the most widely referenced standard for determining the tensile properties of elastomers.

This chapter describes tensile testing of advanced ceramic materials, a category that includes both noncomposite, or monolithic, ceramics and ceramic-matrix composites (CMCs). The chapter presents four key considerations that must be considered when carrying out tensile tests on advanced monolithic ceramics and CMCs. These include effects of flaw type and location on tensile tests, separation of flaw populations, design strength and scale effects, and lifetime predictions and environmental effects. The chapter discusses the advantages, problems, and complications of four basic categories of tensile testing techniques as applied to ceramics and CMCs. These categories are true direct uniaxial tensile tests at ambient temperatures, indirect tensile tests, tests where failure is presumed to result from tensile stresses, and high-temperature tensile tests.

This chapter presents the fundamentals of tensile testing of fiber-reinforced polymer composites. Basic tensile testing of polymer composites is divided into lamina and laminate testing. The chapter focuses on tensile testing of laminates. It discusses the most common tensile test methods that have been standardized for fiber-reinforced composite materials. It also briefly reviews considerations in tensile testing of metal-matrix composites.

This chapter focuses on tensile testing of three types of engineering components that undergo significant loading in tension, namely, threaded fasteners and bolted joints; adhesive joints; and welded joints. It describes the standardized tensile test for externally threaded fasteners and provides a brief background on relationships among torque, angle-of-turn, tension, and friction. The chapter also describes the test methods covered in the ASTM F 606M standard, namely, product hardness; proof load by length measurement, yield strength, or uniform hardness; axial tension testing of full-sized products; wedge tension testing of full-sized products; tension testing of machined test specimens; and total extension at fracture testing. Finally, the chapter covers tensile testing of adhesive and welded joints.

This chapter focuses on short-term tensile testing at high temperatures. It emphasizes one of the most important reasons for conducting hot tensile tests: the determination of the hot working characteristics of metallic materials. Two types of hot tensile tests are discussed in this chapter, namely, the Gleeble test and the conventional isothermal hot-tensile test. The discussion covers equipment used and testing procedures for the Gleeble test along with information on hot ductility and strength data from this test. The chapter describes the stress-strain curves, material coefficients, and flow behavior determined in the isothermal hot tensile test. It also describes three often-overlapping stages of cavitation during tensile deformation, namely, cavity nucleation, growth of individual cavities, and cavity coalescence.

This chapter details low-temperature test procedures and equipment. It discusses the role temperature plays in the properties of typical engineering materials. The effect that lowering the temperature of a solid has on the mechanical properties of a material is summarized for three principal groups of engineering materials: metals, ceramics, and polymers (including fiber-reinforced polymers). The chapter describes the factors that influence the selection of tensile testing procedures for low-temperature evaluation, along with a comparison of tensile and compression tests. It covers the parameters and standards related to low-temperature tensile testing. The chapter discusses the factors involved in controlling test temperature. Finally, the chapter discusses the safety issues concerning the use of cooled methanol, liquid-nitrogen, and liquid helium.

High strain rate tensile testing is used to understand the response of materials to dynamic loading. The behavior of materials under high strain rate tensile loads may differ considerably from that observed in conventional tensile tests. This chapter discusses the processes involved in determining strain rate effects in tension by conventional tensile tests and covers expanding ring tests, flat plate impact tests, split-Hopkinson pressure bar tests, and rotating wheel tests.

This appendix lists approximate equivalent hardness numbers and tensile strengths for Vickers hardness numbers for steel.

This appendix lists approximate equivalent hardness numbers and tensile strengths for Brinell hardness numbers for steel.

This appendix lists approximate equivalent hardness numbers and tensile strengths for Rockwell C and B hardness numbers for steel.