Metal particles were frequently detected in the oil of an aircraft engine, triggering an investigation that led to a torque sensor and its mounting components. The sensor assembly was removed and examined in greater detail. As the chapter explains, investigators discovered that one of the bearings had been subjected to excessive friction, evidenced by brinelling, metal flow, heat tinting, deformation, and wear. They also observed extensive grooving on a retaining plate and several washers matching the diameter of the outer bearing races. Based on their findings, investigators concluded that excessive clearance allowed the outer bearing races to rotate, thus removing material from adjacent contact surfaces and accelerating the buildup of metal particles in the engine oil. The chapter recommends several design changes to remedy the problem.

The wear caused by contact stress fatigue is the result of a wide variety of mechanical forces and environments. This chapter discusses the characteristics of four types of contact stress fatigue on mating metal surfaces: surface, subsurface, subcase, and cavitation. Features and corrective actions for these contact stress fatigue are discussed. The chapter also lists some possible ways to reduce the cavitation fatigue problem.

This chapter discusses the causes and effects of wear along with prevention methods. It covers abrasive, erosive, erosion-corrosion, grinding, gouging, adhesive, and fretting wear. It also discusses various forms of contact-stress fatigue, including subsurface-origin fatigue, surface-origin fatigue, subcase-origin fatigue (spalling fatigue), and cavitation fatigue.

This chapter reviews the types of friction that are of concern in tribological systems along with their associated causes and effects. It discusses some of the early discoveries that led to the development of friction laws and the understanding that friction is a system effect that can be analyzed based on energy dissipation. It describes the stick-slip behavior observed in wiper blades, the concept of asperities, and the significance of the shape, lay, roughness, and waviness of surfaces in sliding contact. It explains how friction forces are measured and how they are influenced by speed, load, and operating environment. It also covers rolling contact and fluid friction and the effect of lubrication.

This chapter discusses the processes and procedures involved in tribotesting, the significance of test parameters and conditions, and practical considerations including test metrics and measurements and the interpretation of wear damage. It also describes the different types of erosion tests in use and common approaches for adhesive wear and abrasion testing.

This chapter discusses the effect of friction in the context of design. It explains how friction coefficients are determined and how they are used to make sizing and selection decisions. It covers practical issues associated with rolling friction, the use of lubricants, and the tribology of metal, ceramic, and polymer surfaces in contact. It also discusses the nature of rolling friction and provides helpful design guidelines.

This chapter covers the friction and wear behaviors of plastics and elastomers. It begins by describing the molecular differences between the two types of polymers and their typical uses. It then discusses the important attributes of engineering plastics and their suitability for applications involving friction, erosion, and adhesive and abrasive wear. It also discusses the tribology of elastomers and rubber along with their basic differences and the conditions under which they produce Schallamach waves. It includes information on polymer composites as well.

This chapter covers the tribological properties of stainless steel and other corrosion-resistant alloys. It describes the metallurgy and microstructure of the basic types of stainless steel and their suitability for friction and wear applications and in environments where they are subjected to liquid, droplet, and solid particle erosion. It also discusses the tribology of nickel- and cobalt-base alloys as well as titanium, zinc, tin, aluminum, magnesium, beryllium, graphite, and different types of wood.

This chapter covers common types of erosion, including droplet, slurry, cavitation, liquid impingement, gas flow, and solid particle erosion, and major types of wear, including abrasive, adhesive, lubricated, rolling, and impact wear. It also covers special cases such as galling, fretting, scuffing, and spalling and introduces the concepts of tribocorrosion and biotribology.

Gears can fail in many different ways, and except for an increase in noise level and vibration, there is often no indication of difficulty until total failure occurs. This chapter begins with the classification of gear failure modes, followed by sections discussing the characteristics of various fatigue failures. Then, it provides information on the modes of impact fractures, wear, scuffing, and stress rupture. Next, the chapter describes the causes of gear failures and discusses the processes involved in conducting the failure analysis. Finally, the chapter presents examples of gear failure analysis.

This article focuses on friction and wear as they relate to polymeric materials, covering friction and wear applications for polymeric materials. The discussion covers the causes and mechanisms of friction, wear, and lubrication; different test methods developed to simulate friction and wear mechanisms; and friction and wear test data used for polymeric materials.

This chapter provides an overview of the thermodynamics of extrusion. It begins by presenting a thermodynamic model of the extrusion process expressed in the form of finite difference equations. It then explains how the model accounts for multiple sources of heat generation, the influence of principal variables on temperature rise, and different types of temperature measurements. It also discusses the benefits of isothermal extrusion and how it achieves consistent mechanical properties in extruded components.

This chapter discusses the basic differences between direct and indirect extrusion, the application of plastic theory, the significance of strain and strain rate, friction, and pressure, and factors such as alloy flow stress and extrusion ratio, which influence the quality of material exiting the die and the amount of force required.

This chapter covers the tribological properties of different types of oil, greases, solid lubricants, and metalworking and traction fluids. It explains how lubricants are made, how they work, and how they are applied and tested. It also discusses the fundamentals of lubrication and friction control, the relationship between viscosity and breakaway friction, and the factors that affect load-carrying capacity and service life.

This chapter discusses five forms of mechanically assisted degradation of metals: erosion, fretting, fretting fatigue, cavitation and water drop impingement, and corrosion fatigue. Emphasis is placed on the mechanisms and the factors affecting these forms of degradation.

This chapter provides guidelines and insights on the selection of materials, coatings, and treatments for friction and wear applications. It begins with a review of the system nature of tribological effects, the subtleties of friction, and the selection idiosyncrasies of the material systems and lubricants covered in prior chapters. It then presents a systematic approach for selecting tribomaterials, using an automotive fan motor as an example.

This chapter summarizes the various kinds of gear wear and failure and how gear life in service is estimated and discusses the kinds of flaws in material that may lead to premature gear fatigue failure. The topics covered are alignment, gear tooth, surface durability and breakage of gear tooth, life determined by contact stress and bending stress, analysis of gear tooth failure by breakage after pitting, and metallurgical flaws that reduce the life of gears. The chapter briefly reviews some components in the design and structure of each gear and/or gear train that must be considered in conjunction with the teeth to enhance fatigue life.

This chapter discusses the formation of free carbides and their effect on case-carburized components. It explains how alloying elements influence the composition and structure of carbide phases produced at cooling rates typical of carburizing process. It describes the morphology and distribution of the various types of carbides formed and explains how they affect mechanical properties such as hardness, residual stresses, fatigue and fracture behaviors, and wear resistance. It also provides guidance for determining what processing conditions to avoid and when and why parts should be rejected.

This chapter is a detailed account of the general characteristics and effects of and the methods for preventing or reducing different categories of wear failures, namely abrasive (erosive, grinding, and gouging), adhesive, and fretting wear.