1-20 of 2180 Search Results for

steel casting

Sort by
Image
Published: 01 December 1995
Fig. 10-18 Conveyor belt pulley casting. Original steel casting, top, and redesigned cast-weld construction More
Image
Published: 01 June 2008
Fig. 19.7 Continuous steel casting. Source: Ref 1 More
Image
Published: 01 March 2002
Fig. 7.15 Microstructure of an AISI/SAE 4327 steel casting that was sectioned by electric discharge machining (EDM). (a) Low-magnification view of the cut surface. (b) Melted and solidified region at the surface. (c) Heat-affected zone. (d) Base bainitic microstructure. 4% picral plus HCl etch More
Image
Published: 01 August 2018
Fig. 8.8 Macrograph of the transverse section of a steel casting for railway application. Solidification shrinkage can be observed at the region of cross section change. Etched with HCl (stains close to the pores are caused by poor drying practice after etching). When only shrinkage More
Image
Published: 01 August 2018
Fig. 8.9 Macrograph of the transverse section of a steel casting for railway application. Presence of porosity in the thickest section of the part. A weld repair region can also be seen at the bottom and to the right of the figure. (see Chapter 14, “Structural Steels and Steels for Pressure More
Image
Published: 01 August 2018
Fig. 8.30 Interdendritic porosity (microporosity) in a steel casting containing 0.28% C, quenched and tempered. The shape of porosity in castings is very similar to the shape of the interdendritic spaces. Optical micrograph. 2% nital etching (porosity is visible without etching). More
Image
Published: 01 August 2018
Fig. 8.31 Severe porosity in a steel casting. Optical micrograph. No etching. More
Image
Published: 01 August 2018
Fig. 8.39 Macrograph of a large (14 t) steel casting. The large interdendritic spacing indicates slow cooling. The straight axes of the dendrites indicate that no mechanical work was performed on the part (i.e., that this is not a wrought steel part: see Chapter 11, “Hot Working More
Image
Published: 01 August 2018
Fig. 8.61 Macrograph of a plane transverse to a fracture in a steel casting. (The fracture surface is at the bottom of the image.) The central region of the casting presents strong “V” segregation and some porosity. Etchant: hot hydrochloric acid More
Image
Published: 01 November 2013
Fig. 14 Continuous steel casting. Source: Ref 13 More
Image
Published: 01 December 1995
Fig. 15-16 Ultrasonic inspection of a steel casting on the shop floor More
Image
Published: 01 December 1995
Fig. 2-12 Trailer or truck wheel spider steel casting More
Image
Published: 01 December 1995
Fig. 2-67 A scarifier assembly steel casting to prepare heavy and rocky ground. The replaceable tips are also steel castings. More
Image
Published: 01 December 1995
Fig. 2-90 Single-piece steel casting is the fluid end of a slush pump. More
Image
Published: 01 December 1995
Fig. 2-104 5-ton capacity crane hook steel casting quenched and tempered to 120 to 150 ksi (827 to 1034 MPa) tensile strength More
Image
Published: 01 December 1995
Fig. 2-135 Front wheel arm steel casting More
Image
Published: 01 December 1995
Fig. 3-8 Comparison of steel casting and weldment for the same service to illustrate the professional appearance necessary for sales appeal. Height 16 in. (40.6 cm). Section thickness 3/4 in. (19 mm). Weight 100 lb (45 kg). The casting customer reported, “the castings were considerably neater More
Image
Published: 01 December 1995
Fig. 10-9 Steel casting tamper tip [3.75 × 2.25 in. (95 × 64 mm)] replacing a forging More
Image
Published: 01 December 1995
Fig. 10-23 Steering arm as a weldment, left, and as a steel casting More
Image
Published: 01 December 1996
Fig. 6-11 Microstructure from a steel casting showing dendrites. The variation in the Mn content and microhardness (DPN) from a region along the mid-line of the micrograph is also shown. The dendritic segregation of Mn is revealed in the microstructure due to different amounts of primary α More