1-10 of 10 Search Results for

spring clip fasteners

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290207
EISBN: 978-1-62708-306-5
... system. The chapter then describes important structural fasteners, namely bolts, screws, pins, collar fasteners, rivets, blind fasteners, machine pins, and spring clip fasteners. The following sections describe the process involved in presses, shrink fits, hole generation, and fastener installation. The...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230441
EISBN: 978-1-62708-298-3
.... Cure samples under a pressure of approximately 97 kPa (applied by weight or spring) for 16 h at 23 °C followed by 2 h at 82 °C. Fig. 24.8 Effect of operating temperature on the tensile strength of beryllium, steel, and titanium bonded with polyimide adhesives. Source: Snogren 1970...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.tpmpa.t54480353
EISBN: 978-1-62708-318-8
... predominant alloy used, other alloys used in aircraft applications are Ti-13V-11Cr-3Al and Ti-3Al-8V-6Cr-4Zr-4Mo in fasteners and springs; Ti-10V-2Fe-3Al and Ti-6Al-6V-2Sn in forgings; commercially pure, Ti-15V-3Al-3Cr-3Sn, and Ti-3Al-2.5V as hydraulic tubing; and Ti-6Al-4V extralow interstitial, Ti-10V-2Fe...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2008
DOI: 10.31399/asm.tb.fahtsc.t51130087
EISBN: 978-1-62708-284-6
... leaving the subject of deformation, consider a small spring clip that was designed to be used at the top of the linear portion of the stress-strain curve. Why would anyone design a spring to be used at a stress almost at the nominal yield strength? No experienced metallurgical engineer would expect each...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2001
DOI: 10.31399/asm.tb.aub.t61170457
EISBN: 978-1-62708-297-6
... conditions, and the room-temperature strengths and fatigue resistances of these alloys depend on the amount of cold work as well as the alloy content. Typical applications of cold-worked wrought alloys (cold-worked tempers) include springs; fasteners, hardware, small gears, cams, electrical contacts, and...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2000
DOI: 10.31399/asm.tb.ttg2.t61120295
EISBN: 978-1-62708-269-3
... RMI Titanium Co. 1000 Warren Ave. Niles, OH 44446 Tel: 330-544-7633 Fax: 330-544-7796 Producer of titanium and titanium alloys in sheets, strip, ingots, plates SAES Getterrs/U.S.A., Inc. 1122 E. Cheyenne Mountain Blvd. Colorado Springs, CO 80906 Tel: 719-576-3200 Fax: 719-576-5025 Ultrapure...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090367
EISBN: 978-1-62708-266-2
... 1). Many so-called constant-strain tests, particularly if a spring is included in the stressing system, are not actually constant-strain tests, because a significant amount of elastic strain energy may be contained in the stressing system. Depending on the “softness” of the spring or the elasticity...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910237
EISBN: 978-1-62708-250-1
..., appliances, automotive body panels, fasteners, and hardware items. Fig. 11 Service life (time to 5% rusting of steel surface) versus thickness of hot dip galvanized (zinc) coating for selected atmospheres Atmosphere Description Heavy industrial atmospheres These contain general...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2018
DOI: 10.31399/asm.tb.aceg.t68410151
EISBN: 978-1-62708-280-8
... either bump pin actuation or spring actuation. Mold and core coatings wear out due to continuous operation. Periodic mold and core touch-up by mold conditioners extends the life of coatings up to three to five shifts. If the coating touch-up is not done on time there can be buildup of...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.caaa.t67870219
EISBN: 978-1-62708-299-0
... Treatment of Aluminum Alloys.” The latter specification covers tests that are required for periodic monitoring of 2 xxx and 7 xxx series alloys in all rivets and fastener components as well as sheet, bar, rod, wire, and shapes under 6.4 mm (0.25 in.) thick. Alloys in this series that contain more than...