1-20 of 364 Search Results for

shear test

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870351
EISBN: 978-1-62708-314-0
... Abstract This chapter discusses composite testing procedures, including tension, compression, shear, flexure, and fracture toughness testing as well as adhesive shear, peel, and honeycomb flatwise tension testing. It also discusses specimen preparation, environmental conditioning, and data...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910427
EISBN: 978-1-62708-250-1
..., metallurgical condition, and product form, rather than specimens that are the most expedient for the investigation. For example, it might seem advantageous to obtain flat, uniform disk specimens by machining slices from an extruded rod rather than by shearing or stamping test coupons from rolled sheet (and...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610025
EISBN: 978-1-62708-303-4
... embrittlement. The chapter also covers compression, shear, and torsion testing, the prediction of yielding, residual stress, and hardness. compression hardness notched tensile test shear stress-strain curve tension MANY MATERIALS, both during initial fabrication and later when placed in service...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 April 2013
DOI: 10.31399/asm.tb.imub.t53720117
EISBN: 978-1-62708-305-8
... strength and ductility. It is good practice to examine the test piece surface for deep scratches, gouges, edge tears, or shear burrs. These discontinuities may sometimes be minimized or removed by polishing or, if necessary, by further machining; however, dimensional requirements may often no longer be...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2008
DOI: 10.31399/asm.tb.emea.t52240201
EISBN: 978-1-62708-251-8
... Abstract The mechanical behavior of a material is its response to an applied load or force. Important mechanical properties are strength, hardness, stiffness, and ductility. This chapter discusses three principal ways in which these properties are tested: tension, compression, and shear...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270141
EISBN: 978-1-62708-301-0
...-defined chevron marks along the fracture surface that end in a shear lip on the convex side. Further examination using a SEM shows that the failure was due to overload. Based on these observations and the results of tensile testing and microstructural analysis, investigators concluded that a sudden impact...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090367
EISBN: 978-1-62708-266-2
... Abstract This chapter addresses the challenge of selecting an appropriate stress-corrosion cracking (SCC) test to evaluate the serviceability of a material for a given application. It begins by establishing a generic model in which SCC is depicted in two stages, initiation and propagation, that...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 April 2013
DOI: 10.31399/asm.tb.imub.t53720393
EISBN: 978-1-62708-305-8
... Abstract Fabricated powder metallurgy (P/M) parts are evaluated and tested at several stages during manufacturing for part acceptance and process control. The various types of tests included are dimensional evaluation, density measurements, hardness testing, mechanical testing, and...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780185
EISBN: 978-1-62708-281-5
.... Mechanical tests under tensile, compressive, flexural, and shear loading can be performed as either short-term tests or long-term tests of creep deformation. Data for the long-term tests are typically recorded as time-dependent displacement values at various levels of constant stress ( Fig. 15a ). This type...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270082
EISBN: 978-1-62708-301-0
... Abstract This chapter discusses the investigation of a helicopter tail rotor blade that fractured during a test flight. It includes images of the damaged blade along with close-ups of both sides of the blade tip showing that the tip tore off at the rivets. Based on their observations...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270168
EISBN: 978-1-62708-301-0
... shearing of the screws that hold it in place. They also provided recommendations to remediate the problem. locking screws low pressure turbine discs macrostructural evaluation SEM fractography visual examination During cyclic spin tests on an LP turbine disc of an aircraft engine...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780238
EISBN: 978-1-62708-281-5
... in HIPS as the fatigue test progresses. These events are understandable, considering ABS undergoes shear yielding mechanisms and the HIPS undergoes crazing that requires a tensile component of stress. Crazing results from fibrillation or polymeric drawing ahead of the fatigue flaw. The advancement of...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780216
EISBN: 978-1-62708-281-5
... Abstract This article discusses the material and engineering issues associated with plastic components subjected to impact. The first part covers the effects of loading rate, temperature, and state of stress on both deformation and mode of failure. It discusses standard impact tests, along with...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780259
EISBN: 978-1-62708-281-5
... Abstract This article focuses on friction and wear as they relate to polymeric materials, covering friction and wear applications for polymeric materials. The discussion covers the causes and mechanisms of friction, wear, and lubrication; different test methods developed to simulate friction...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780211
EISBN: 978-1-62708-281-5
... Abstract This article briefly describes the historical development of fracture resistance testing of polymers and reviews several test methods developed for determining the fracture toughness of polymeric materials. The discussion covers J-integral testing, the methods for determining linear...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 February 2005
DOI: 10.31399/asm.tb.chffa.t51040025
EISBN: 978-1-62708-300-3
... Abstract This chapter explains how to determine flow stress and forgeability using data from tensile tests, compression tests, ring tests, and torsion tests. It describes sample preparation, tooling and equipment, test procedures, error sources, and data plotting techniques. It also provides a...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060149
EISBN: 978-1-62708-261-7
... Abstract This chapter explains how metallography and hardness testing are used to evaluate the quality and condition of metal products. It also discusses the use of tensile testing, fracture toughness and impact testing, fatigue testing, and nondestructive test methods including ultrasonic, x...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.cw.t51820203
EISBN: 978-1-62708-339-3
... lines, ultrasonic testing was carried out. The ultrasonic test procedure was standardized earlier in the laboratory with mock up welded pipe standards having reference defects. An ultrasonic flaw detector with a 2.25 MHz frequency, 45° angle shear wave probe was used for testing purpose. Clear defect...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1984
DOI: 10.31399/asm.tb.mpp.t67850334
EISBN: 978-1-62708-260-0
... Abstract Hardness tests provide valuable information about the quality of materials and how they are likely to perform in different types of service. This chapter covers some of the most widely used hardness testing methods, including Vickers, Rockwell, and Brinell tests, Shore scleroscope and...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2011
DOI: 10.31399/asm.tb.cfw.t52860095
EISBN: 978-1-62708-338-6
... 58 ( No. 4 ), Dec 2002 , p 529 – 537 10.1016/S0263-8223(02)00162-9 8.52 Walrath D.E. and Adams D.F. , The Iosipescu Shear Test as Applied to Composite Materials , Exp. Mech. , March 1983 , p 105 – 110 10.1007/BF02328688 8.53 Kedward K.T. , On the Short...