This chapter discusses the effect of friction in the context of design. It explains how friction coefficients are determined and how they are used to make sizing and selection decisions. It covers practical issues associated with rolling friction, the use of lubricants, and the tribology of metal, ceramic, and polymer surfaces in contact. It also discusses the nature of rolling friction and provides helpful design guidelines.

The wear caused by contact stress fatigue is the result of a wide variety of mechanical forces and environments. This chapter discusses the characteristics of four types of contact stress fatigue on mating metal surfaces: surface, subsurface, subcase, and cavitation. Features and corrective actions for these contact stress fatigue are discussed. The chapter also lists some possible ways to reduce the cavitation fatigue problem.

This chapter discusses the causes and effects of wear along with prevention methods. It covers abrasive, erosive, erosion-corrosion, grinding, gouging, adhesive, and fretting wear. It also discusses various forms of contact-stress fatigue, including subsurface-origin fatigue, surface-origin fatigue, subcase-origin fatigue (spalling fatigue), and cavitation fatigue.

One of the rotor bearings in an electric motor failed, producing excessive vibrate. The bearing was removed and disassembled, revealing craters and bruises on the inner ring raceway and balls along with evidence of melting and burning of metal. Scanning electron microscopy revealed metal particles near the craters, and energy-dispersive x-ray analysis showed that slivers recovered from the grease had the same composition as the bearing raceway and balls. Based on these observations, it was concluded that the bearing failed due to electrostatic discharge, which would have led to seizure if it continued. The report recommends the use of electrically conductive grease and proper grounding practices.

This chapter reviews the types of friction that are of concern in tribological systems along with their associated causes and effects. It discusses some of the early discoveries that led to the development of friction laws and the understanding that friction is a system effect that can be analyzed based on energy dissipation. It describes the stick-slip behavior observed in wiper blades, the concept of asperities, and the significance of the shape, lay, roughness, and waviness of surfaces in sliding contact. It explains how friction forces are measured and how they are influenced by speed, load, and operating environment. It also covers rolling contact and fluid friction and the effect of lubrication.

This chapter presents the purpose, design, and function of a gear. It also presents the basic stresses applied to a gear tooth. The chapter provides an overview on the bending strength and characteristics of the gear tooth.

Prior to forging, it is often necessary to preform billet stock to achieve adequate material distribution. This chapter discusses the equipment used for such operations, including transverse rolling machines, electric upsetters, ring-rolling mills, horizontal presses, and rotary (orbital) and radial forging machines. It describes their basic operating principles as well as advantages and disadvantages.

This chapter concerns itself with the tribology of ceramics, cermets, and cemented carbides. It begins by describing the composition and friction and wear behaviors of aluminum oxide, silicon carbide, silicon nitride, and zirconia. It then compares and contrasts the microstructure, properties, and relative merits of cermets with those of cemented carbides.

Rolling is unique in that it cannot be conducted without friction. Friction draws the workpiece into the roll gap and facilitates its passage through the deformation zone. This chapter provides an overview of the mechanics and tribology of flat rolling processes and explains how various aspects of the theory apply to shape rolling as well. It derives numerous equations and models to help quantify the forces, torque, and power involved in rolling operations and the associated heating, slip, strain distribution, and deformation in both the workpiece and rolls. It describes the friction and wear that occur in hot and cold rolling under hydrodynamic and mixed-film lubrication; the influence of viscosity, film thickness, rolling speed, interface pressure, pass reduction, and lubricant breakdown; and the effect of surface finish and defects. The chapter also provides best practices for evaluating, applying, and treating lubricants for industrially important materials including iron-base, nickel-base, and aluminum alloys.

This chapter covers common types of erosion, including droplet, slurry, cavitation, liquid impingement, gas flow, and solid particle erosion, and major types of wear, including abrasive, adhesive, lubricated, rolling, and impact wear. It also covers special cases such as galling, fretting, scuffing, and spalling and introduces the concepts of tribocorrosion and biotribology.

This chapter discusses the processes and procedures involved in tribotesting, the significance of test parameters and conditions, and practical considerations including test metrics and measurements and the interpretation of wear damage. It also describes the different types of erosion tests in use and common approaches for adhesive wear and abrasion testing.

This chapter provides an overview of the rolling and finishing processes required to create a sheet, plate, or foil product from a direct chill (DC) cast ingot. The flow paths, equipment, and operations are described with a view to the basic evolution of the microstructure, surface characteristics, and dimensions.

This chapter describes the classification of steels and the various compositional categories of commercial steel products. It explains how different alloying elements affect the properties of carbon and low-alloys steels and discusses strength, toughness, and corrosion resistance and how to improve them.

This chapter covers the friction and wear behaviors of carbon, alloy, and tool steels. It begins a review of commercially available shapes and forms. It then describes the metallurgy and microstructure of various designations and grades of each type of steel and explains how it affects their performance in adhesive and abrasive wear applications and in environments where they are subjected to solid particle, droplet, slurry, and cavitation erosion and fretting damage.