1-20 of 344 Search Results for

rod

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270078
EISBN: 978-1-62708-301-0
...Abstract Abstract This chapter explains how investigators determined that a stabilizer link rod fractured due to overload, possibly by a combination of tension and bending forces that occurred during an accident. It includes images comparing the fractured rod with its undamaged counterpart...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270080
EISBN: 978-1-62708-301-0
...Abstract Abstract A tie rod on a 70-ton aircraft towing tractor failed during a test run, fracturing near a welded bracket that connects to a hydraulic jack. This chapter discusses the failure and the investigation that followed. It presents a close-up view of the fracture surface showing what...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270185
EISBN: 978-1-62708-301-0
...Abstract Abstract A pair of bolts on a connecting rod failed during a test run for a prototype engine. They were replaced by bolts made from a stronger material that also failed, one due to fatigue, the other by tensile overload. The fracture surfaces on all four bolts were examined using...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.ex2.t69980059
EISBN: 978-1-62708-342-3
... compressive load on the hollow stem; F VSt , axial compressive stress on the sealing stem; s , sealing stem displacement Abstract Abstract This chapter opens with a discussion of the classification of rod and tube extrusion processes. The standard processes involve hot working (extrusion...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.ex2.t69980323
EISBN: 978-1-62708-342-3
... The machinery and equipment required for rod and tube extrusion is determined by the specific extrusion process. This chapter provides a detailed description of the design requirements and principles of machinery and equipment for direct and indirect hot extrusion. It then covers the presses and auxiliary...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.aacppa.t51140175
EISBN: 978-1-62708-335-5
... for aluminum alloy 238.0-F, permanent mold. Test specimen: 1.125 diam × 12 in. rod Fig. D2.2 Growth and hardness curves for aluminum alloy 242.0-F, permanent mold. Test specimen 1.125 diam × 12 in. rod Fig. D2.3 Growth and hardness curves for aluminum alloy 242.0-T4, permanent mold...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.smnm.t52140039
EISBN: 978-1-62708-264-8
... cylindrical rod, is pulled apart in a machine that applies a known force, F . The machine has grips attached to the ends of the cylindrical metal rod, and the force is applied parallel to the axis of the rod, as shown schematically at the right in Fig. 5.1 . As the force increases, the rod gets longer...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270100
EISBN: 978-1-62708-301-0
... of normal as well as emergency lowering procedures. After various maneuvers and final landing, it was found that the universal joint on the actuating link rod of the inboard door of the starboard undercarriage was broken. Investigations revealed that the link rod had fractured due to the propagation...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smff.t53400145
EISBN: 978-1-62708-316-4
..., a clutch/brake, a drive shaft, a connection (also called a pitman arm or connecting rod), and a slide (ram) guided by the gibs ( Fig. 10.1 ). Depending on the design, a press may have gear set(s) to reduce the speed and increase the torque ( Ref 10.2 , 10.3 , 10.4 ). Fig. 10.1 Schematic...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 February 2005
DOI: 10.31399/asm.tb.chffa.t51040185
EISBN: 978-1-62708-300-3
... of ForgePAL is included in Appendix 15.1 , given on the CD attached to this book. 15.5.1 Connecting Rod Forging 15.5.2 Forging of a Lead Disk with Flash Appendix 15.1: ForgePAL: A Computer Program for Estimating Forces in Hot Forging with Flash Any arbitrary three-dimensional forging...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2016
DOI: 10.31399/asm.tb.ascaam.t59190001
EISBN: 978-1-62708-296-9
... Partially modified Fine plates, partial fragmentation 4 Rods, no plates, some needles are accepted 5 Completely modified Rods, no needles 6 Fine rods, invisible under light microscope Source: Ref 72 Morphological effects of eutectic silicon modification Table 1.7 Morphological...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.smnm.t52140099
EISBN: 978-1-62708-264-8
... a simple experiment. The experiment is done with two short lengths of drill rod having a diameter of 3 mm (⅛ in.). Drill rod is either 1095 steel or W1 tool steel, both of which have essentially the same composition. One-inch long sections at the midpoints of the two rods are simultaneously heated...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270084
EISBN: 978-1-62708-301-0
... of two halves held together by three tie-rods, 120° apart. These hubs are made of magnesium-aluminum alloy. Figure CH10.2 shows clearly the separation of one-half of the hub toward outboard and the complete absence of the flange. The tire is held in position by the two flanges. Fig. CH10.1...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 February 2005
DOI: 10.31399/asm.tb.chffa.t51040211
EISBN: 978-1-62708-300-3
.... 17.1 Schematic illustration of forming sequences in cold forging of a gear blank. (a) Sheared blank. (b) Simultaneous forward rod and backward extrusion. (c) Forward extrusion. (d) Backward cup extrusion. (e) Simultaneous upsetting of flange and coining of shoulder [ Sagemuller, 1968 ] Fig...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2000
DOI: 10.31399/asm.tb.aet.t68260001
EISBN: 978-1-62708-336-2
... basic types of extrusion are direct and indirect, which are commonly used in aluminum industries as shown in Fig. 1 and 6 . Solid and hollow shapes are designed and extruded for a wide range of programs: Solid sections, bars, and rods extruded from solid billets by direct extrusion (discussed...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2015
DOI: 10.31399/asm.tb.cpi2.t55030247
EISBN: 978-1-62708-282-2
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smff.t53400129
EISBN: 978-1-62708-316-4
..., “Mechanical Presses,” in this book. The kinematics of the slide motion are determined by the main drive (i.e., crank and connecting rod or pitman arm). The available machine load ( L M ) is a function of stroke( s ). Energy-Restricted Machines: Although not commonly used in sheet metal forming...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.spsp2.t54410315
EISBN: 978-1-62708-265-5
... and Applications of Metal Wires , Paris H.G. and Kim D.K. , Ed., TMS , Warrendale, PA , 1996 , p 3 – 15 15.34 Ferrous Wire — Vol 1 , Chapter 5A, Controlled Cooling of Wire Rod , Wire Handbook 15.35 Keyser P.L. and Kiefer B.V. , STELMOR In-Line Controlled Cooling Process...
Series: ASM Technical Books
Publisher: ASM International
Published: 15 June 2021
DOI: 10.31399/asm.tb.mpktmse.t56010019
EISBN: 978-1-62708-384-3
... Problem 25 Calculate the stress in a 0.5-in.-diameter rod that is loaded with 1000 lb. Solution Calculate the stress in a 10-mm-square rod pulled along its axis with a 10,000-N load. Solution A 0.5-in. diameter, 10-in.-long bar lengthens by 0.010 in., determine the strain in the bar...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2000
DOI: 10.31399/asm.tb.aet.t68260055
EISBN: 978-1-62708-336-2
... and higher speeds to improve physical and mechanical properties of the extrusion. The press requires a rigid structure with a tie rod and platen to withstand the associated stresses. Modern presses use prestressed tie-rod construction with long die stacks to provide minimum deflection to improve...