Irradiation-assisted stress-corrosion cracking (IASCC) has been a topic of engineering interest since it was first reported in the 1960s, having been observed in stainless steel cladding on light water reactor fuel elements. This chapter summarizes the results of decades of investigation, showing that IASCC can essentially be defined as the intergranular cracking of austenitic alloys in high-temperature water, where both the material and its environment have been altered by radiation. Of the many interactions that can occur when metals and water are exposed to radiation, the international consensus is that the three with the greatest impact on crack growth rates are the formation of material defects, radiation-induced segregation, and chemical reactions that increase the corrosion potential of water. The chapter discusses each of these in great detail, and includes information on predictive modeling as well.

This chapter describes the conditions under which environmental degradation is likely to occur in polymer matrix composites and the potential damage it can cause. It discusses the problems associated with moisture absorption and exposure to solvents, fuels, ultraviolet radiation, lightning strikes, thermal oxidation, and extreme temperatures. It also discusses the factors that influence flammability.

A test flight was cut short after a fire warning came on indicating a problem with one of the four engines on an aircraft. A visual examination following the precautionary landing revealed several burned hoses, a melted bolt, and fuel leaking from the base of the main burner. The fuel nozzle was also damaged, and based on its microstructure, came very close to melting. Investigators determined that the burner was mounted backwards, facing the compressor rather than the turbine. They also recommended a redesign to prevent the fuel nozzle from being reversed.

This chapter discusses the use of nondestructive inspection methods, including visual, ultrasonic, radiographic, and thermographic techniques, and the types of flaws and damages they can reveal in composite parts and assemblies. It describes the basic principles behind each method along with best practices and procedures.

This chapter discusses the basic steps of a failure investigation. It explains that the first step is to gather and document information about the failed component and its operating history. It advises investigators to visit the failure site as soon as possible to record damages and collect test specimens for subsequent examination and chemical analysis. It also discusses the role of mechanical property testing, the use of nondestructive evaluation, and the final step of generating a report.

This chapter provides an overview of the various inspection methods used with metals and alloys, namely visual inspection, coordinate measuring machines, machine vision, hardness testing, tensile testing, chemical analysis, metallography, and nondestructive testing. The nondestructive testing methods discussed are liquid penetrant inspection, magnetic particle inspection, eddy current inspection, radiographic inspection, and ultrasonic testing.

This chapter discusses radiography methods using x-rays, gamma rays, and neutrons. It begins with a discussion on the applications and principles of radiography followed by sections providing information on the sources of radiation, classifications, and characteristics of x-ray tubes. Three primary attenuation processes of electromagnetic radiation, namely photoelectric effect, Compton scattering, and pair production, are covered. The chapter then discusses the principles of shadow formation, the process involved in the conversion of radiation into a form suitable for observation, and the characteristics of x-ray film. It provides information on various exposure factors in film radiography. The chapter provides a description of the characteristics that differentiate neutron radiography from x-ray or gamma ray radiography. The application of neutron radiography is described in terms of its advantages for improved contrast on low atomic number materials, discrimination between isotopes, or inspection of radioactive specimens.

This chapter discusses the techniques applicable to the diagnosis of corrosion failures, including visual and microscopic examination of corroded surfaces and microstructure; chemical analysis of the metal, corrosion products, and bulk environment; nondestructive evaluation methods; corrosion testing techniques; and mechanical testing techniques. A guide to investigative techniques used in corrosion failure analysis is provided in a table, describing the advantages and limitations of each technique. The principal stages of the investigation and analysis of corrosion failures discussed in the chapter are: collection of background information and sampling; preliminary laboratory examination; detailed metallographic and fractographic examinations; chemical analysis of corrosion products and bulk materials; corrosion testing for quality control; mechanical testing for quality control; and analysis of results and report writing.

This article depicts typical fractographic features for a number of different composite materials, covering interlaminar and translaminar fracture characteristics in composite materials.

X-ray imaging systems have long played a critical role in failure analysis laboratories. This article begins by listing several favorable traits that make X-rays uniquely well suited for non-destructive evaluation and testing. It then provides information on X-ray equipment and X-ray microscopy and its application in failure analysis of integrated circuit (IC) packaging and IC boards. The final section is devoted to the discussion on nanoscale 3D X-ray microscopy and its applications.

This chapter concentrates almost exclusively on inspection techniques related to pressure vessels and pipework. The discussion covers the general aspects associated with inspection and the key factors relevant to it. In addition, the chapter addresses processes involved in data collection and management, namely data acquisition, reporting, trending, reviewing, and auditing. Capabilities and limitations of in-service inspection techniques are discussed in the Appendix to this chapter.

Most of the counterfeit parts detected in the electronics industry are either novel or surplus parts or salvaged scrap parts. This article begins by discussing the type of parts used to create counterfeits. It discusses the three most commonly used methods used by counterfeiters to create counterfeits. These include relabeling, refurbishing, and repackaging. The article presents a systematic inspection methodology that can be applied for detecting signs of possible part modifications. The methodology consists of external visual inspection, marking permanency tests, and X-ray inspection followed by material evaluation and characterization. These processes are typically followed by evaluation of the packages to identify defects, degradations, and failure mechanisms that are caused by the processes (e.g., cleaning, solder dipping of leads, reballing) used in creating counterfeit parts.

Polymer composite materials are subject to degradation if not appropriately protected from the environment. Composite materials having polymeric matrices are susceptible to degradation from heat, sunlight, ozone, atomic oxygen (in space), moisture, solvents (chemicals), fatigue, excessive loading, and combinations of these environmental conditions. This chapter discusses the effects of heat, ultraviolet-light, and atomic oxygen on composite materials.

This chapter briefly outlines some of the basic aspects of failure analysis, describing some of the basic steps and major concerns in conducting a failure analysis. A brief review of failure types from fracture, distortion, wear-assisted failure, and environmentally assisted failure (corrosion) is also provided.

This chapter discusses design and certification considerations, including materials and process selection, the building block approach to certification, design allowables, and design guidelines. It also includes information on damage tolerance and environmental sensitivity.

This article reviews fatigue test methodologies, provides an overview of general fatigue behavior (crack initiation and propagation) in engineering plastics, and discusses some of the factors affecting the fatigue performance of polymers. In addition, it provides information on fractography that provides useful insight into the nature of fracture processes.

This article is a detailed account of the mechanisms of fatigue failure of polymers, namely thermal fatigue failure and mechanical fatigue failure. The mechanical fatigue failure is discussed in terms of fatigue crack initiation and fatigue crack propagation.

This chapter examines the static, fatigue, and damage tolerance properties of glass, aramid, and carbon fiber systems. It also explains how delaminations, voids, porosity, fiber distortion, and fastener hole defects affect impact resistance and strength.

Welded joints in any component or structure require a thorough inspection. The role of nondestructive evaluation (NDE) in the inspection of welds is very important, and the technology has become highly developed as a result. This article describes the applications, methods, evaluation procedures, performance, and limitations of NDE. It provides information on the training and certification of NDE operators, evaluation of test results, and guidance to method selection. Typical examples of various NDE methods for welds are also described.