1-10 of 10 Search Results for

polycrystalline diamond insert cutters

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2013
DOI: 10.31399/asm.tb.mfub.t53740213
EISBN: 978-1-62708-308-9
...), and polycrystalline diamond (PCD). The different materials vary greatly in wear resistance and toughness. A schematic of their relative application ranges in terms of machining speeds and feed rates is shown in Fig. 15 . Higher machining speeds require tool materials with greater wear resistance, whereas higher feed...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.stg2.t61280189
EISBN: 978-1-62708-267-9
... steels and most of the other metals, cutters with carbide inserts were employed. For the nickel-base superalloys, the speeds shown are based on cutters with high-speed steel inserts. The slowest speeds, 20 sfm (6 m/min), were required for the three nickel-base superalloys (Rene 41, U-500, and U-700...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870307
EISBN: 978-1-62708-314-0
... and delaminations under the force of fastener installation. Countersinking cutters for composites are normally made of solid carbide, steel with carbide inserts, or steel with PCD inserts. When a hole is placed in a composite laminate, it creates a stress concentration and the overall load-bearing capacity...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2008
DOI: 10.31399/asm.tb.emea.t52240411
EISBN: 978-1-62708-251-8
... for polycrystalline diamond-brazed tools, such as high-speed machining of aluminum as well as nonmetallic materials such as graphite, ceramics, and advanced composites. Diamond films are produced using a modified CVD process. Diamond-coated cutting tools work in a way analogous to a grinding wheel. The cutting edge...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550457
EISBN: 978-1-62708-307-2
... in the Honda Prelude since 1990, displacing cast iron inserts ( Fig. 9.2 ). In the manufacturing process, the engine block casting and piston liner preform infiltration are performed simultaneously, eliminating the cost of assembly associated with the cast iron inserts. More importantly, the MMC liners provide...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870537
EISBN: 978-1-62708-314-0
... problem than excessive heat generation. Polycrystalline diamond cutting tools exhibit longer lives than either solid or diamond-coated carbide tools but are also more expensive. They also require a rigid setup to prevent edge chipping. Other methods, such as abrasive water jet cutting and wire electrical...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.9781627083232
EISBN: 978-1-62708-323-2
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.t69870375
EISBN: 978-1-62708-344-7
... of the Ceramic Design Process , Ceramics and Glasses , Vol 4 , Engineered Materials Handbook, ASM International , 1991 , p 676 – 689 A.40 Knudsen F.P. , Dependence of Mechanical Strength of Brittle Polycrystalline Specimens on Porosity and Grain Size , J. Am. Ceram. Soc. , Vol 42 (No. 8...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.9781627083447
EISBN: 978-1-62708-344-7
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2001
DOI: 10.31399/asm.tb.aub.9781627082976
EISBN: 978-1-62708-297-6