1-20 of 43 Search Results for

nut projection

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870307
EISBN: 978-1-62708-314-0
... locators. Another recent development is the use of laser projection units for establishing part and hole location. A typical application for a laser projection system is shown in Fig. 11.3 . Fig. 11.3 Laser projection location. Source: Laser Projection Technologies, Inc. It is important...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290061
EISBN: 978-1-62708-306-5
... of the upper electrode (compare with Fig. 3.8b ). Nugget diameter, penetration, and shear strength continue to increase as weld time progresses. Figure 3.8(d) shows the fully developed weld nugget. Projection welding is used where there is a high thickness ratio (e.g., nuts welded to sheet) and where...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.tpmpa.t54480265
EISBN: 978-1-62708-318-8
.... The success of the early trials led to the formation of a TWI Group-Sponsored Project (GSP) in 1996. Under this GSP, several TWI member companies jointly funded a research program on FSW of titanium alloys, which ran from 1996 through 2002. Friction Stir Welding of Ti-6Al-4V The majority of work during...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 November 2013
DOI: 10.31399/asm.tb.uhcf3.t53630117
EISBN: 978-1-62708-270-9
... are present; however, when there is a macroscopic projection on one surface, there is a depression on the opposing surface. Fig. 14 Schematic, highly enlarged sketch of a typical fatigue-fracture surface. Sketch shows three origins (stage 1) at O; thousands of microscopic, closely spaced fatigue...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smff.t53400233
EISBN: 978-1-62708-316-4
.... clinch nut die See nutter die. closed hem See flattened hem. coining (1) A closed-die squeezing operation in which all surfaces of a work piece are con- fined or restrained, resulting in a well-defined imprint of the die on the work. (2) A restrik- ing operation used to sharpen or change an existing...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smff.9781627083164
EISBN: 978-1-62708-316-4
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060117
EISBN: 978-1-62708-261-7
... on surface quality. In order of increasing quality and cost, they are: Industrial quality Cold heading quality Recessed head or scrapless nut quality Special head quality Cold turned, ground, or shaved wire (seamless) Coining Coining is a compression-type operation in which...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1999
DOI: 10.31399/asm.tb.cmp.t66770099
EISBN: 978-1-62708-337-9
... not greatly affect the surface hardness of carburized and hardened surfaces and only marginally influences the core hardness. For high-carbon martensite, Kelly and Nutting ( Ref 16 ) considered that grain size has a negligible influence on the increase of hardness, and other factors, such as carbon in solid...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.tpmpa.t54480001
EISBN: 978-1-62708-318-8
... group metals. Just one year later, in 1971, with the cancellation of the U.S. SST project, the titanium market reached another low, with just 9.26 million kg (20.4 million lb) of mill product shipments. In 1974, production rebounded to 15.8 million kg (34.8 million lb), and by 1978 a new peak...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.t60490183
EISBN: 978-1-62708-340-9
... 18. Baker R.G. and Nutting J. , The Tempering of 2¼Cr-1Mo Steel After Quenching and Normalizing , J. Iron Steel Inst ., July 1959 , p 257 - 269 19. Numerous papers in Life Extension and Assessment of Fossil Power Plants , Dooley R.B. and Viswanathan R. , Ed...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 1988
DOI: 10.31399/asm.tb.eihdca.t65220185
EISBN: 978-1-62708-341-6
... to couple heat to a greater depth at the end of a shaft, it will do the same at holes, long slots, or projections ( Fig. 8.15 ). If the part contains a circular hole, an additional eddy-current path is produced which will cause heating at a rate considerably higher than that in the rest of the part...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.ex2.t69980323
EISBN: 978-1-62708-342-3
... subassemblies: Main cylinder: One or two piece; housing and main cylinder Platen: One piece with or without a discard shear and/or with a discard saw Columns: Round columns with inboard and external nuts, round columns with compression sleeves (tubular) and external nuts, lamellar tension...
Series: ASM Technical Books
Publisher: ASM International
Published: 31 December 2020
DOI: 10.31399/asm.tb.phtbp.t59310127
EISBN: 978-1-62708-326-3
... for low-alloy steels should reflect the effect of the alloying additions on the critical temperature. Empirical formulas have been generated to project, roughly, the effect of alloying additions (and residual elements) on the eutectoid, or critical, temperature. A representative relationship for common...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.mgppis.t60400087
EISBN: 978-1-62708-258-7
... in each specimen. Most times, these measurements can be made with the aid of a simple metallographic microscope with a scale of measurement installed in an eyepiece, or by projecting the image on a ground glass screen. In larger operations, where thousands of repetitive measurements are made, a computer...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.t60490001
EISBN: 978-1-62708-340-9
...-1Mo A199,A200,A213,A335,A369,A426 … A217 A182 Ferritic and austenitic stainless steels A213,A249,A268,A269,A27l,A312,A358,A362,A376,A409,A430,A451,A452,A511 A167,A176,A240,A412,A457 A296,A297,A351,A447,A448 A182,A336,A473 (a) Carbon and alloy steel bolts and nuts are covered...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.tb.msisep.t59220353
EISBN: 978-1-62708-259-4
... in the steel by making them richer in calcium ( Fig. 11.25 ). Fig. 11.21 (a) Effect of the inclusion projected length on the tested area on the energy absorbed in the upper shelf of Charpy-V impact tests for a C-Mn structural steel for different specimen orientations. (b) Nomenclature adopted for planes...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780064
EISBN: 978-1-62708-281-5
... of the stress may manifest itself as postmold shrinkage. Holes and Other Features Injection-molded part features can be expressed as a function of the nominal wall thickness ( T ) as shown in Fig. 8 and 9 . Fig. 8 Good design practice for holes and projections in injection-molded parts...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2010
DOI: 10.31399/asm.tb.hss.t52790257
EISBN: 978-1-62708-356-0
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.ex2.9781627083423
EISBN: 978-1-62708-342-3
Series: ASM Technical Books
Publisher: ASM International
Published: 30 November 2013
DOI: 10.31399/asm.tb.uhcf3.9781627082709
EISBN: 978-1-62708-270-9