1-20 of 86 Search Results for

nonferrous filler metal

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2010
DOI: 10.31399/asm.tb.hss.t52790235
EISBN: 978-1-62708-356-0
... was president of Arcos, a welding filler metal company in Philadelphia. The UNS W-series was set aside for ferrous and nonferrous welding alloys. Welding filler metals that are similar to the basic stainless steels in the S-series would be included in the S-series, with the numbers 80 to 89 in the last two...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 1997
DOI: 10.31399/asm.tb.wip.t65930179
EISBN: 978-1-62708-359-1
... requirements. The article discusses the processes involved in welding process selection and the methods of preparing base metal for repair welding. It presents the guidelines for weld repairs of various ferrous (carbon steels, cast irons, and stainless steels) and nonferrous (for example, titanium) base metals...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2015
DOI: 10.31399/asm.tb.cpi2.t55030112
EISBN: 978-1-62708-282-2
... IT IS NOT UNUSUAL to find that, although the wrought form of a metal or alloy is resistant to corrosion in a particular environment, the welded counterpart is not. Further, welds can be made with or without the addition of filler metal. However, there are also many instances in which the weld exhibits corrosion...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.cw.t51820169
EISBN: 978-1-62708-339-3
... be considered. When dissimilar metals are joined by arc (fusion) welding processes, alloying between the base metals and a filler metal; when used, becomes a major consideration. The resulting weld metal can behave much differently from one or both base metals during subsequent processing or in service...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290079
EISBN: 978-1-62708-306-5
... groove, fillet, plug, or slot welds in metal ranging from thin sheet to heavy castings. Weld layers can be built up, as in oxyfuel gas welding. The process is often used as a low-temperature substitute for oxyfuel gas welding. Braze welding resembles brazing in that nonferrous filler metals are used...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2001
DOI: 10.31399/asm.tb.aub.t61170550
EISBN: 978-1-62708-297-6
... melting temperatures and are less fluid. For food-processing applications, where toxicity must 552 / Other Nonferrous Alloys Table 2 Nominal composition and solidification temperatures for silver-base brazing filler metals Composition, wt% Solidification temperatures AWS Other Brazing desig- elements...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.cw.t51820143
EISBN: 978-1-62708-339-3
... among the base (parent) metal, the filler metal, and the heat-affected regions where microstructural changes have been produced. Corrosion Resistance Wrought aluminum alloys can be classified as either non-heat treatable alloys or heat treatable alloys ( Table 1 ). The corrosion resistance...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290165
EISBN: 978-1-62708-306-5
..., eutectic BAg Preforms, foil, powder Most ferrous and nonferrous metals, except aluminum and magnesium Most widely used utility filler metals TM-Si-B (b) , eutectic ... ... ... ... (Ni/Fe + Cr)-Si-B BNi Powder, tape (c) , RS foil AlSl 300 and 400 series steels and nickel- and cobalt-base...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 1997
DOI: 10.31399/asm.tb.wip.t65930365
EISBN: 978-1-62708-359-1
... Abstract This appendix provides reference tables listing weldability of cast irons, steels, and nonferrous metals. A process selection table for arc welding carbon steels is included, and recommended preheat and interpass temperature tables are also presented. This appendix includes information...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.tt2.t51060091
EISBN: 978-1-62708-355-3
... Typical room-temperature tensile properties of nonferrous alloys Table 2 Typical room-temperature tensile properties of nonferrous alloys Metal or alloy Approximate composition, % Condition 0.2% offset tensile yield strength, MPa (ksi) Tensile strength, MPa (ksi) Tensile modulus...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.lmcs.t66560427
EISBN: 978-1-62708-291-4
... on a fractured surface, free of laminations or shaletype discontinuities. filler metal. Metal added in making a brazed, soldered, or welded joint. final annealing. An imprecise term used to denote the last anneal given to a nonferrous alloy prior to shipment. finish annealing. A subcritical annealing treatment...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2000
DOI: 10.31399/asm.tb.ttg2.t61120143
EISBN: 978-1-62708-269-3
... been reprinted from Heat Treater’s Guide: Practices and Procedures for Nonferrous Alloys (edited by H. Chandler, ASM International, 1996); however, they provide far more than just heat treating data. Many of the datasheets include information on compositions and specifications, general...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060117
EISBN: 978-1-62708-261-7
... and pickup truck bodies. Fig. 6.8 Production mill processes Ingot Breakdown Many ingots continue to be statically cast, because not all ferrous and nonferrous metals are capable of being continuously cast. Due to their relatively coarse and inherently weak microstructure, the temperature...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1995
DOI: 10.31399/asm.tb.sch6.t68200369
EISBN: 978-1-62708-354-6
.... Thermit welding, with its high heat input and its characteristically slow cooling rate is generally not used unless austenitic manganese filler is applied along with subsequent heat treatment. Resistance welding is practiced on a commercial basis usually joining small castings to sheet metal. Electroslag...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 1997
DOI: 10.31399/asm.tb.wip.9781627083591
EISBN: 978-1-62708-359-1
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.stg2.t61280149
EISBN: 978-1-62708-267-9
... welding techniques, defect prevention, fixturing, heat treatments, and general practices, including the use of filler metals. It also discusses several solid-state welding methods, superplastic forming, and transient liquid phase bonding, a type of diffusion welding process. The chapter includes extensive...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.lmcs.9781627082914
EISBN: 978-1-62708-291-4
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290023
EISBN: 978-1-62708-306-5
... to a large and diversified group of welding processes that use an electric arc as the source of heat to melt and join metals. The formation of a weld between metals that are arc welded may or may not require the use of a filler metal. The welding arc is struck between the workpiece and the tip...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060429
EISBN: 978-1-62708-261-7
..., and volumet- to suitable temperatures and by using a filler ric modulus of elasticity. metal having a liquidus above 450 °C (840 burnishing. Finish sizing and smooth finishing °F) and below the solidus of the base metal. of surfaces (previously machined or ground) by displacement, rather than removal, of min...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.9781627082617
EISBN: 978-1-62708-261-7