1-20 of 1060 Search Results for

metal thickness

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 30 September 2023
Figure 8.26: Film thickness developed in metal rolling of aluminum with an emulsion lubricant [ 73 ]. The rolling speed was (a) u = 0.127 m/s; (b) u = 0.254 m/s. More
Image
Published: 01 December 2003
Fig. 32 Nonlinear regions for metal and plastic plates. σ, stress; t , thickness More
Image
Published: 01 January 2015
Fig. 12.9 Comparison of total metal allowance as a function of stock thickness in flash welding titanium and steel. Allowances include metal loss in the flashing and upsetting operations. More
Image
Published: 01 June 1983
Figure 10.5 Variation of fluoride film thickness on metal powders exposed to fluorine gas at 193 K ( Kleinberg and Tompkins, 1962 ). More
Image
Published: 01 November 2007
Fig. 11.13 Tube wastage data, which included both metal loss (tube thickness loss) and total wastage (metal loss+intergranular penetration), for ferritic steels and austenitic stainless steels in terms of chromium concentration in alloys. The data were generated in a boiler at Bromborough More
Image
Published: 01 November 2007
Fig. 12.9 Maximum thickness loss of corrosion probes exposed at metal temperature 550 °C (1020 °F) for 3000 h in WTE boilers as a function of the sum of heat of fusion (corresponding to the amount of fused salt) of the deposits. The open data points are Type 347H, and the solid data points More
Image
Published: 01 December 2016
Fig. 3.5 Microstructure of alloy AlSi7Mg, metal mold, wall thickness 2 cm. (a–f) Silicon in the interdendritic eutectic, lamellae and rods of eutectic silicon. (e) Enlarged microregion visible in (d). SEM, deep etch More
Image
Published: 01 December 2016
Fig. 3.6 Microstructure of alloy AlSi7Mg, metal mold, wall thickness 1 cm. (a–f) Silicon in the interdendritic eutectic, lamellae and rods of eutectic silicon particles. SEM, deep etch More
Image
Published: 01 December 2016
Fig. 3.20 Microstructure of alloy AlSi11, metal mold, wall thickness 2 cm. (a–f) Silicon in the interdendritic eutectic, lamellae of eutectic silicon. SEM, deep etch More
Image
Published: 01 December 2016
Fig. 3.21 Microstructure of alloy AlSi11, metal mold, wall thickness 1 cm. (a–f) Silicon in the interdendritic eutectic, lamellae and rods of eutectic silicon. SEM, deep etch More
Image
Published: 01 November 2019
Figure 5b CMP directly to thick metal pitch layer More
Image
Published: 01 August 1999
Fig. 11.22 (Part 1) Electroslag butt weld in 0.2% C 50 mm thick plate. Weld metal: 0.16C-0.37Si-0.90Mn (wt%). (a) # Transverse section. 3% nital. 1.25×. (b) Weld metal. 170 HV. 1% nital. 1 O×. (c) Weld metal: grain-boundary region. 1% nital. 100×. (d) Weld metal: center of a grain. 1 More
Image
Published: 01 August 1999
Fig. 11.23 Electroslag butt weld in 0.15% C 50 mm thick plate. Weld metal: 0.16C-0.37Si-0.90Mn (wt%). (a) and (b) Weld metal, as deposited. 170 HV. Picral. 1000×. (c) and (d) Weld metal, after weldment has been austenitized at 925 °C and cooled at 500 °C/h. 125 HV. (c) 1% nital. 100 More
Image
Published: 01 April 2004
Fig. 4.2 A porous ceramic material metallized with a thick silver electroplate. The residual stress in the metallization has resulted in a peel failure through the near-surface layer of the ceramic. More
Image
Published: 01 November 2013
Fig. 6 Three lubrication regimes experienced in sheet metal forming. (a) Thick-film lubrication. (b) Thin-film lubrication. (c) Boundary lubrication. Source: Ref 3 More
Image
Published: 01 November 2013
Fig. 19 Typical setup for press-brake forming in a die with a vertical opening. R , punch radius; s , span width; r , die radius; t , metal thickness. Source: Ref 12 More
Image
Published: 01 October 2012
Fig. 2.16 Typical setup for press brake forming in a die with a vertical opening. R , punch radius; r , die radius; s , span width; t , metal thickness. Source: Ref 2.15 More
Image