Mechanical treatments such as grinding and shot peening are often employed in the production of case-carburized parts. Grinding, besides restoring precision, removes carbide films, internal oxidation, and high-temperature transformation products. Shot peening strengthens component surfaces and induces a stress state that increases fatigue resistance. This chapter describes both processes as well as roller burnishing. It explains how these treatments are applied and how they influence the microstructure, properties, and behaviors of case-hardened components. It also addresses process challenges, particularly in regard to grinding.

This chapter discusses the factors influencing the corrosion resistance of bulk materials, namely alloying, metallurgical factors, and mechanical treatments.

This chapter addresses the general effects of composition, mechanical treatment, surface treatment, processing, and fabrication operations on the corrosion resistance of aluminum and its alloys. Different types of surface treatments covered include claddings, anodizing, and conversion coatings. The processing steps that can have relatively significant impact on corrosion resistance are homogenization, rolling, extrusion, quenching, aging, and annealing.

The basic concept for most methods of corrosion protection is to remove one or more of the electrochemical cell components so that the pure metal or metal alloy of interest will not corrode. Another widely used corrosion protection approach is to change the nature of the anode so that it becomes the cathode (cathodic protection). This chapter briefly reviews these methods of corrosion protection. The factors affecting corrosion behavior are covered. In addition, the chapter provides information on coatings and inhibitors, which are used in corrosion protection.

The metallurgy of aluminum and its alloys offers a range of opportunities for employing heat treatments to obtain desirable combinations of mechanical and physical properties such that castings meet defined temper requirements. This chapter discusses the processes involved in solution heat treatment, quenching, precipitation hardening, and annealing of aluminum alloys. The effects of these processes on dimensional stability and residual stresses are also discussed. Troubleshooting and diagnosis of heat treating problems are covered in the concluding section of the chapter.

This appendix provides information on temper designations for strain-hardened aluminum, heat treatable aluminum alloys, and annealed aluminum products.

This chapter discusses the composition, alloying characteristics, mechanical properties, corrosion resistance, advantages, limitations, and applications of martensitic, semiaustenitic, and austenitic precipitation-hardenable stainless steels.

Engineered geometry and its microstructures impact casting performance. This chapter describes three interdependent disciplines that are needed to achieve product performance and cost targets, namely engineered geometry; target microstructure and chemistry; and optimum process for high integrity.

Stainless steels and nickel-base alloys are recognized for their resistance to general corrosion and other categories of corrosion. This chapter examines the effects of specific alloying elements, metallurgical structure, and mechanical conditioning on the corrosion resistance of these alloys. Some categories of corrosion covered are pitting, crevice, intergranular, stress-corrosion cracking, general, and high-temperature corrosion.

This chapter provides an outline of the failure modes and mechanisms associated with most boiler tube failures in coal-fired power plants. Primary categories include stress rupture failures, water-side corrosion, fire-side corrosion, fire-side erosion, fatigue, operation failures, and insufficient quality control.

The stress-strain curves in this data set are representative examples of the behavior of several cast alloys under tensile or compressive loads. The curves are arranged by alloy designation. Each figure cites the original source of the curve and provides pertinent background information as available. Compressive tangent modulus curves are presented for certain alloys. The effects of cyclic loading are given on several curves.

This chapter briefly discusses the characteristics of mechanical twins and stacking faults in close-packed planes. It provides an overview of the composition, microstructures, thermodynamics, processing, deformation mechanism, mechanical properties, formability, and special attributes of twinning-induced plasticity steels.

This chapter provides guidelines on how to set up and run an effective quality-improvement program for aluminum extrusion operations. It begins by identifying production processes and variables that impact the quality of hard and soft alloy extrusions. It then presents a series of checklists and flowcharts that can be used to monitor and troubleshoot billet-making and extrusion processes, die construction, equipment maintenance, heat treating, and sawing and stretching procedures. It also discusses the importance of charting test results and monitoring surface treatments that may be required to improve corrosion, oxidation, or wear resistance.

This chapter contains a list of technical papers and books related to the heat treatment of gears.

Temperature and deformation gradients developed in the course of manufacturing can have undesired effects on the microstructures along their path; the two most common being residual stress and distortion. This chapter discusses these manufacturing-related problems and how they can be minimized by heat treatments. It also provides information on residual stress evaluation and prediction techniques.

This chapter describes heat treatments that produce uniform grain structures, reduce residual stresses, and improve ductility and machinability. It also discusses spheroidizing treatments that improve strength and toughness by promoting dispersions of spherical carbides in a ferrite matrix. The chapter concludes with a brief discussion on the mechanical properties of ferrite/pearlite microstructures in medium-carbon steels.

This chapter discusses the compositions, metallurgical phases, microstructure, heat treatment, grades, and structure-property relationships of steels. In addition, it describes the mechanisms involved in deformation, strengthening, and annealing of steels.

Martensitic steels are produced by quenching carbon steel from the austenite phase into martensite. This chapter provides information on the composition, microstructures, processing, deformation mechanisms, mechanical properties, hot forming, tempering, and special attributes of martensitic steels.