1-20 of 141 Search Results for

material safety data sheets

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230499
EISBN: 978-1-62708-298-3
...-exposure limit is 2 μg/m 3 , and the permissible-action level limit is 0.2 μg/m 3 . The Brush Wellman Material Safety Data Sheet, No. M10, revised on January 1, 2002, indicated an 8 h TWA permissible-exposure limit of 2 μg/m 3 . (Brush Wellman, Inc. is the sole current producer of beryllium...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.omfrc.t53030089
EISBN: 978-1-62708-349-2
... composites Magnaflux Zyglo (Magnaflux Corp.) penetrants: Nontranslucent fiber composites (a) Read the material safety data sheets for each of these materials. The dyes are toxic by ingestion and also can be absorbed through the skin. One of the easiest ways to dye microcracks in composites...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.tb.hpcspa.t54460107
EISBN: 978-1-62708-285-3
... nitrogen and helium are noncorrosive, special materials are not required. Material safety data sheets and standard design codes should be used when dealing with nitrogen. ...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.omfrc.t53030023
EISBN: 978-1-62708-349-2
... complete. In addition to these materials, commercial suppliers of consumables have their own set of dyes that can be used for this purpose. Caution: Read the material safety data sheets to handle appropriately. In Table 2.1 , the dye that finds the most use is Rhodamine B, due to its function and cost...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.mgppis.t60400087
EISBN: 978-1-62708-258-7
.... This information is located at the “right-to-know” stations located at the entrance to the metallographic laboratory. Here you will find a book containing a materials safety data sheet (MSDS) for each of the chemicals and materials used in the laboratory. Always consult the MSDS if you are not sure about...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.tb.ahsssta.t53700071
EISBN: 978-1-62708-279-2
... and then starts to decrease due to localized necking that leads to fracture. Engineering stress-strain curves provide essential information on the deformation properties of materials. The curves reveal basic data on the strength, ductility, hardening capacity, and toughness of engineering materials. Figure...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230523
EISBN: 978-1-62708-298-3
... 10.1557/JMR.1993.1550 Brush Wellman , 2001 . “ Designing with Beryllium ,” Brochure 517, Cleveland, OH Brush Wellman , 2002 . “ Material Safety Data Sheet No. M10 ,” Cleveland, OH Brush Wellman , 2005a . “ Safety Practices for Working with Beryllium Products ,” Brush Wellman...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.9781627082983
EISBN: 978-1-62708-298-3
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060407
EISBN: 978-1-62708-261-7
... in the automotive applications of high-strength steels (HSS) and AHSS is based on the many advantages that such materials offer over mild steel, aluminum, and magnesium alloys. Some of these advantages are: Weight reductions through reduced sheet thickness Safety improvement through high crash resistance...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.tb.ahsssta.t53700001
EISBN: 978-1-62708-279-2
... safety, ensure product reliability, and increase affordability have prompted the auto industry and material suppliers to develop a wide range of solutions to meet these requirements. The solutions include: optimization of product design, incorporation of lightweight materials, utilization of downgaging...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550193
EISBN: 978-1-62708-307-2
...-Protection Surface Treatments and Coatings 4.12 Health and Safety Acknowledgments References References 4.1 Stonehouse A.J. and Marder J.M. , Beryllium , Properties and Selection: Nonferrous Alloys and Special-Purpose Materials , Vol 2 , ASM Handbook , ASM International...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550621
EISBN: 978-1-62708-307-2
... material system. When working with any new material, especially any polymer-based material, it is also important to closely examine the material safety data sheet. The lightweight materials covered in this book included metals (aluminum, magnesium, beryllium, titanium, and titanium aluminide...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2015
DOI: 10.31399/asm.tb.cpi2.t55030360
EISBN: 978-1-62708-282-2
... , “ Reliability Assessment for Containers of Hazardous Material (RACH) ,” 2000 • Health and Safety Executive (UK) HSE , “ Best Practice for the Procurement and Conduct of Non-Destructive Testing, Part 1: Manual Ultrasonic Inspection ,” 2000 • Health and Safety Executive (UK) HSE , “ Best...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870489
EISBN: 978-1-62708-314-0
... process Table 18.4 Typical material product forms versus process Material form Process Pultrusion RTM Compression molding Filament winding Hand lay-up Auto tape laying Discontinuous Sheet molding compound … … • … … … Bulk molding compound … … • … … … Random...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.mgppis.t60400169
EISBN: 978-1-62708-258-7
... for a Two-Dimensional View Grinding Media Adhesive Backing versus Plain Backing The Technique of Grinding Grinding Time Wheel Speed during Grinding Coolant Storage of Grinding Papers Safety during Grinding Mounting Materials Mold Sizes Thermosetting Mounting Materials...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.tb.ems.t53730081
EISBN: 978-1-62708-283-9
... dangerous than the large shards produced in fracture of untempered glass. Tempered glass is used for the side and rear windows of automobiles for these reasons. The windshields of automobiles are made from safety glass produced by laminating two pieces of glass with a polymeric material (polyvinyl butyral...
Book Chapter

By A. Wehrstedt
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.htpa.t53310235
EISBN: 978-1-62708-346-1
... DIN 50115, with additional notched bar impact tests proven in Germany, and possibilities of their analysis For DIN EN 10002-1 (Tensile test on metallic materials): Remnant Standard DIN 50125, with concrete data on usable tensile test pieces Remnant standards are, above all, indisputable when...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smff.t53400005
EISBN: 978-1-62708-316-4
... as prediction of metal flow and elimination of forming defects, depends on the accurate determination of the flow properties of the starting material. The flow curves ( Eq 2.1 ) for sheet materials are usually determined based on load versus elongation data obtained from tensile tests. For a given...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870063
EISBN: 978-1-62708-314-0
... hazardous to the health and safety of the workers, it is again important to coordinate with the material supplier and closely examine the Material Safety Data Sheet (MSDS) for any new material. Since the brittleness of thermosetting polymers is a direct consequence of their high crosslink densities, one...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290207
EISBN: 978-1-62708-306-5
... failure of a new fastener system for a critical application. The designer must not extrapolate existing data to a different size of the same fastener, because larger-diameter fasteners have significantly lower fatigue endurance limits than do smaller-diameter fasteners made from the same material using...