Contaminants can be a cause of numerous types of system failures. There are numerous techniques for confirming contaminant presence. When the presence of a contaminant is suspected, the failure analysis team must find and eliminate the contaminant source, which can be obvious or quite subtle. This chapter summarizes a few commonly encountered contaminant sources to stimulate the reader's thinking about potential contaminant sources. A case study of titanium component washing at Litton Lasers is presented to illustrate how the presence of contaminants leads to a system failure.

Sand and metallic charge materials are two essential and heavy raw materials that are needed for molding and casting. This chapter focuses on planning and provision for storage and handling of the raw materials needed for casting manufacturing. The major raw materials used for molding and casting are metallic charge materials and nonmetallic materials. The chapter also presents the advantages, limitations, and applications of drum or rotary dryers (also known as rotary kiln dryers) and fluidized bed dryers (also known as vibration fluidized bed dryers).

Because of its speed and ease of control, induction heating can be readily automated and integrated with other processing steps such as forming, quenching, and joining. Completely automated heating/handling/control systems have been developed and are offered by induction equipment manufacturers. This chapter deals with materials handling and automation. First, it summarizes basic considerations such as generic system designs, fixture materials, and special electrical problems to be avoided. Next, it describes and provides examples of materials-handling systems in induction billet heating, bar heating, heat treatment, soldering, brazing, and other induction-based processes. The final section discusses the use of robots for parts handling in induction heating systems.

This chapters discusses the considerations involved in the qualification and analysis of induction hardening treatments. The discussion covers material selection and prior heat treatment, hardness and case depth, frequency selection, power density and heating time, part and process tolerances, geometrical effects, quenchant selection, coil design, and work-handling equipment. The chapter also presents several examples, walking readers though each step, and discusses the development of setup instructions and operating procedures.

Most of the counterfeit parts detected in the electronics industry are either novel or surplus parts or salvaged scrap parts. This article begins by discussing the type of parts used to create counterfeits. It discusses the three most commonly used methods used by counterfeiters to create counterfeits. These include relabeling, refurbishing, and repackaging. The article presents a systematic inspection methodology that can be applied for detecting signs of possible part modifications. The methodology consists of external visual inspection, marking permanency tests, and X-ray inspection followed by material evaluation and characterization. These processes are typically followed by evaluation of the packages to identify defects, degradations, and failure mechanisms that are caused by the processes (e.g., cleaning, solder dipping of leads, reballing) used in creating counterfeit parts.

Planning and laying out casting facilities involve a number of vital factors, such as available infrastructure, selection of suitable sites, orientation of operations and process flow, markets and products, operating parameters, and targeted hourly output and annual capacity. This chapter presents guiding principles and layout concepts with these factors in mind. It also presents steps for the creation of a plant layout. Plant layout involves the arrangement of processing areas, machinery, and equipment for the efficient conversion of raw materials into finished products. The chapter discusses general guidelines for developing a layout.

Casting is one of the most economical manufacturing processes for providing shape to components of machinery and is used in a wide range of industries. This chapter is a brief account of the advantages, applications, limitations, and market growth of aluminum casting. It also provides information on the process of conversion of steel and iron parts to aluminum.

Steel castings are produced in thousands of designs for different applications. They fill needs in many industries, including transportation, construction machinery, earthmoving equipment, rolling mills, mining, oil and gas exploration, and power generation. This chapter touches upon the variety of applications for which steel castings can be supplied and the ranges of casting size and complexity. Photographs in this chapter provide an understanding of these applications, their size and complexity, and the types of cast steels produced.

Most iron and steel castings are produced by casting into sand molds. Sand cores are needed primarily to form hollow cavities in castings for collapsibility and ease of cleaning. This chapter begins with an overview of the classification of molding and core-making systems. This is followed by a section discussing the process involved in shell molding, along with its applications. A brief description of the special casting processes is then presented. Next, the chapter discusses the processes involved in core making. Further, it provides an overview of casting manufacturing. Finally, the chapter provides information on the factors that influence a casting facility layout.

Stainless steels have a wide variety of applications for household products, food-handling equipment, major appliances, medical equipment, and industrial equipment. Stainless is also featured in many architectural designs and monuments. Many of the most important applications of stainless steel can be found in the transportation industry, where both the cutlery martensitic and the chromium-nickel austenitic stainless steels have been used. This chapter provides a detailed discussion on these applications.

Induction heating is a rapid, efficient technique for producing localized or through heating in a wide range of industries. The economics as well as the technical feasibility of induction heating should be important considerations prior to investing in such a system. A number of cost elements enter into the analysis. These include equipment and energy costs, production lot size and ease of automation, material savings, labor costs, and maintenance requirements. This chapter discusses each of these factors. It compares the cost elements of induction heating with those of its main competitor, gas-fired furnace heating. Several typical examples are provided to illustrate the economic considerations in design and application of induction heating processes.

This chapter covers regulatory requirements, safe handling practices, hazard analysis and control, dismantling and decommissioning, and waste disposal. It also includes references for additional information on government regulations.

After pouring, castings are allowed to solidify and cool. They are later removed from the molds in the shakeout operation. A series of activities then follow, which are generally referred to as finishing and heat treatment. These activities can be broadly categorized as shakeout, abrasive blast cleaning, removal of risers, ingates, and discontinuities, rough inspection, removal of discontinuities, finishing welding, heat treatment, and final visual, dimensional, and NDT inspection. This chapter provides a detailed discussion on these activities.

This chapter covers the different types of extrusion presses in use, discussing their relative advantages, operating parameters, and selection factors. It describes the function of major components, including containers, stems, dummy pads, and die carriers, the maintenance they require, and their impact on productivity and the quality of extrusions. It also discusses the integration of auxiliary equipment such as log heaters and shears, quench systems, die ovens, pullers, stretchers, and stackers.

This chapter provides a brief introduction to manufacturing processes used to produce metal parts and how they differ in terms of achievable geometries, tolerances, surface finishes, and production rate.

This chapter provides an overview of the state of the art in high-pressure cold spray equipment, including both spray systems and gas supply systems. The chapter describes the commercial cold spray systems developed by companies such as Cold Gas Technology (CGT) GmbH, Plasma Giken Company Ltd, Impact Innovations GmbH, and ASB Industries. Typical helium and nitrogen gas systems used in high-pressure cold spray processing are reviewed.

The machinery and equipment required for rod and tube extrusion is determined by the specific extrusion process. This chapter provides a detailed description of the design requirements and principles of machinery and equipment for direct and indirect hot extrusion. It then covers the presses and auxiliary equipment for tube extrusion, induction furnaces for billet processing, handling systems for copper and aluminum alloy products, extrusion cooling systems, and age-hardening ovens. Next, the chapter describes the principles and applications of equipment for the production of aluminum and copper billets. Then, it focuses on process control in both direct and indirect hot extrusion of aluminum alloys without lubrication. The chapter describes the technology of electrical and electronic controls in the extrusion process. It ends with a discussion on the factors that influence the productivity and quality of the products in the extrusion process and methods for process optimization.

Wrought tubular products are nondestructively inspected chiefly by eddy current techniques (including the magnetic flux leakage technique) and by ultrasonic techniques. The methods discussed in this chapter include eddy current inspection, flux leakage inspection, ultrasonic inspection, magnetic particle inspection, liquid penetrant inspection, and radiographic inspection of resistance welded tubular products, seamless steel tubular products, and nonferrous tubular products. This chapter discusses the fundamental factors that should be considered in selecting a nondestructive inspection method and in selecting from among the commercially available inspection equipment. The factors covered are product characteristics, nature of the flaws, extraneous variables, rate of inspection, end effect, mill versus laboratory inspection, specification requirements, equipment costs, and operating costs.

Beryllium-related lung diseases were first reported in the 1930s, several years after the emergence of beryllium metals in manufactured products. Since then, there have been numerous studies around the world and continued refinement of recommendations and safety standards. This chapter provides a summary of the studies that have been conducted along with the findings. It discusses the effects of acute and chronic exposure, toxicity levels, potential sources and risks, treatment, and protective and preventive measures.