1-15 of 15 Search Results for

lot-centered regression analysis

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.t69870179
EISBN: 978-1-62708-344-7
... the entire program on a single batch of material, two lots (1 and 2) of 316 stainless steel were inadvertently used in the program. One lot had a much lower yield strength than the other. Table 8.4 shows the properties of all four materials finally used in the analysis, including the Ti-6Al-4V...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780089
EISBN: 978-1-62708-281-5
... properties of reactive thermoset systems, while the second utilizes these thermal characteristics as the basis for monitoring and control during processing. thermoset resins chromatography infrared spectroscopy physical test thermal analysis THERMOSETTING RESINS are unique among engineering...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230267
EISBN: 978-1-62708-298-3
... (2246 °F) for the high-purity grades were selected. The sintered densities varied from 72 to 98% of theoretical, with the tubular shapes resulting in lower densities than did cylinders. A regression analysis of composition versus density was performed on the density values obtained in several...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610209
EISBN: 978-1-62708-303-4
... in the austenite + ferrite field. Metastable Austenite-Based Steels Transformation-induced plasticity (TRIP) steels with high contents of nickel and manganese retain the high-temperature face-centered cubic austenite at room temperature on quenching. By a judicious choice of composition, this austenite...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.9781627083447
EISBN: 978-1-62708-344-7
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1996
DOI: 10.31399/asm.tb.phtpclas.t64560043
EISBN: 978-1-62708-353-9
... (1954), Ref 2 ) Fig. 3-9 Temperature-time cooling curves for two steels and a cast iron. These curves were for cooling at the center of 7.9 in. diameter cylinders quenched form 1650°F. (From C.R. Wilks, E. Cook and H.S. Avery, Trans. ASM , Vol 35, p 1 (1945), Ref 3 ) In Chapter 4...
Series: ASM Technical Books
Publisher: ASM International
Published: 15 June 2021
DOI: 10.31399/asm.tb.mpktmse.9781627083843
EISBN: 978-1-62708-384-3
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1996
DOI: 10.31399/asm.tb.phtpclas.9781627083539
EISBN: 978-1-62708-353-9
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1984
DOI: 10.31399/asm.tb.mpp.9781627082600
EISBN: 978-1-62708-260-0
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2007
DOI: 10.31399/asm.tb.pmsspmp.9781627083126
EISBN: 978-1-62708-312-6
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090367
EISBN: 978-1-62708-266-2
... on the exterior of the ring by the tightening of a bolt centered on the diameter of the ring. However, an almost constant load can be developed by placing a calibrated spring on the loading bolt. C-rings can also be stressed in the reverse direction by spreading the ring and creating a tensile stress...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1995
DOI: 10.31399/asm.sch6.9781627083546
EISBN: 978-1-62708-354-6
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 1983
DOI: 10.31399/asm.tb.mlt.9781627083485
EISBN: 978-1-62708-348-5
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.9781627082860
EISBN: 978-1-62708-286-0
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.ex2.t69980195
EISBN: 978-1-62708-342-3
... ZnAl15. After hot rolling, extrusion is the most important deformation process for zinc-base alloys, although the main application of zinc alloys is pressure die castings. The extrusion of these alloys has lost a lot of its importance. Zinc alloys are extruded only to a limited extent mainly because...