1-20 of 147 Search Results for

liquidus temperature

Sort by
Image
Published: 01 August 2005
Fig. 2.23 Variation in liquidus temperature and hardness for aluminum-12.6 wt% silicon alloys as a function of copper content More
Image
Published: 01 April 2004
Fig. 5.30 Solidus and liquidus temperatures of 3.8Ag-0.7Cu-95.5Sn solder as a function of the added rare earth (RE) concentration More
Image
Published: 01 January 2015
Fig. 2.21 Liquidus surface of ternary alloy A, B, and C. Temperature, °F More
Image
Published: 01 April 2004
Fig. 5.1 Reduction in the liquidus and solidus temperature of an off-eutectic silver-tin alloy as a function of the bismuth addition More
Image
Published: 01 August 2018
Fig. 17.59 The effect of the difference between the actual sulfur content of a gray cast iron and that needed to cause the precipitation of MnS at the liquidus temperature of the alloy. T ℓ is the liquidus temperature. All experiments performed with S = 0.12% and C eq = 3.8% with different More
Image
Published: 01 August 2018
are below the equilibrium liquidus temperatures, solid interface instabilities grow until they reach the position corresponding to x l . More
Image
Published: 01 July 1997
is greater than the liquidus temperature. More
Image
Published: 01 August 2005
Fig. 2.11 Section through the Ag-Cu-Zn-Cd quaternary system at 40% Ag. The liquidus temperature of alloy compositions is indicated by a series of isotherms. Note: This is not a true ternary phase diagram. Adapted from Petzow and Aldinger [1968] More
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.tb.ems.t53730011
EISBN: 978-1-62708-283-9
... causes the formation of a boundary layer in which liquid near the solid-liquid interface contains more solute than the liquid further away from the boundary ( Fig. 2.11a ). In the liquid there is a variation of the freezing temperature (liquidus temperature) just ahead of the interface, as shown in Fig...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.pb.t51230189
EISBN: 978-1-62708-351-5
... these filler metals have melting points well above 450 °C (840 °F). Their working temperatures are mostly in the range 725 to 925 °C (1340–1700 °F) so that, technically, they are brazes. The liquidus surface of the ternary gold-silver-copper phase diagram is shown in Fig. 5.5 . In consequence of the fact...
Series: ASM Technical Books
Publisher: ASM International
Published: 31 January 2024
DOI: 10.31399/asm.tb.pdktmse.t56100001
EISBN: 978-1-62708-470-3
... binary phase diagrams that account for the presence of inclusions, oxygen content, and secondary phases. binary phase diagrams CALPHAD composition differential scanning calorimetry eutectic point lever rule liquidus temperature phase reactions solidification microstructure solidus...
Image
Published: 01 March 2012
Fig. 13.6 Comparison of calculated liquidus, solidus, and γ′ solvus temperatures with those determined by experiment. Source: Ref 13.4 as published in Ref 13.2 More
Image
Published: 01 January 1998
Fig. 4-27 Liquidus surface at iron-rich corner of the Fe-Cr-C system. Temperatures given in degrees centigrade. Source: Ref 41 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.tpmpa.t54480031
EISBN: 978-1-62708-318-8
... in this chapter). Fig. 2.8 Binary alloy phase diagram of metals A and B that are completely soluble in each other in the solid state. Liquidus line (red) shows the liquid composition at various temperatures as the alloy is slowly cooled (equilibrium is maintained). Solidus line (blue) shows the composition...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2012
DOI: 10.31399/asm.tb.pdub.t53420263
EISBN: 978-1-62708-310-2
... transition temperature ( T r ), which is defined as the ratio of the glass formation temperature and the liquidus temperature, should be on the order of 0.6 or higher. According to this argument, BMGs are often found to form near deep eutectic invariant reactions where high T r can be achieved...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2012
DOI: 10.31399/asm.tb.pdub.t53420239
EISBN: 978-1-62708-310-2
..., if made by melting, or that cannot be melted to a homogeneous liquid can sometimes be produced by powder metallurgy techniques. Contamination from the atmosphere is often very damaging. In extreme cases, the liquidus temperature has been observed to be depressed several hundred degrees simply...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.pb.t51230047
EISBN: 978-1-62708-351-5
... [ Humpston and Jacobson 1993 , Chapter 3 ]. For a braze to be compatible with a particular parent material, it must exhibit these characteristics: It must have a liquidus temperature below the melting point (solidus temperature) of the parent materials. Usually, a margin is required between...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060085
EISBN: 978-1-62708-261-7
... at which solidification begins is called the liquidus temperature , and the equilibrium temperature where solidification is complete is called the solidus temperature . Different alloy compositions have different liquidus and solidus temperatures, and the lines that appear on a binary phase diagram...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2012
DOI: 10.31399/asm.tb.pdub.t53420429
EISBN: 978-1-62708-310-2
... gradient at the liquid-solid interface during solidification. A thermal gradient is most easily controlled by controlling the rate of heat extraction from the casting, or the cooling rate. Alloys that have a wide spread between the liquidus and the solidus temperatures solidify with a mostly equiaxed grain...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2012
DOI: 10.31399/asm.tb.pdub.t53420191
EISBN: 978-1-62708-310-2
... the three faces. Adapted from Ref 10.1 Liquidus Plots The temperature at which freezing begins is shaded in Fig. 10.2 . In Fig. 10.3 , these temperatures for each composition are transferred onto a triangular diagram; the liquidus temperatures are plotted as isothermal contours...