1-20 of 87 Search Results for

interfacial wear

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 2003
Fig. 1 Interfacial wear processes. (a) Initial contact of the two surfaces. (b) Running-in process where the soft polymer molecules are gradually transferred to the hard counterface as third body. (c) Steady-state wear process where the wear and friction phenomena are influenced mainly More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780267
EISBN: 978-1-62708-281-5
... by providing information on the processes involved in interfacial and cohesive wear. This is followed by sections describing the wear process and applications of elastomers, thermosets, glassy thermoplastics, and semicrystalline thermoplastics. The effects of environmental and lubricant on the wear failures...
Image
Published: 01 December 2003
and wear thinning of fibers; 3, interfacial separation of fiber and matrix; 4, fiber cracking; 5, back-transferred polymer or organic fibers (film and layered wear debris) showing delamination and cracking; 6, metallic and wear debris transferred from the counterface; 7, pulled-out or peeled-off fiber More
Image
Published: 01 December 2003
Fig. 2 Relative abrasive wear loss of polymethyl methacrylate (PMMA) and composites filled with quartz and glass against abrasives SiC (45 μm), SiO 2 (10 μm), and CaCO 3 (3 μm) as a function of filler volume fraction, V f . WIB, weak interfacial bond; SIB, strong interfacial bond. 1, WIB More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780276
EISBN: 978-1-62708-281-5
..., SiO 2 , and CaCO 3 abrasives as a function of filler volume fraction. The performance clearly depends on the ratio of hardness of the abrasives to the filler, the interfacial adhesion of the filler with the matrix PMMA, and the volume fraction. Fig. 2 Relative abrasive wear loss of polymethyl...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780259
EISBN: 978-1-62708-281-5
... Abstract This article focuses on friction and wear as they relate to polymeric materials, covering friction and wear applications for polymeric materials. The discussion covers the causes and mechanisms of friction, wear, and lubrication; different test methods developed to simulate friction...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550569
EISBN: 978-1-62708-307-2
... capability, high hardness and wear resistance, low thermal conductivity, and chemical inertness. The high-temperature capability of ceramics makes them very attractive materials for extremely high-temperature environments. However, due to their very low fracture toughness, ceramics are limited in structural...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 November 2013
DOI: 10.31399/asm.tb.uhcf3.t53630169
EISBN: 978-1-62708-270-9
... for the use of transmission oil coolers in racing cars. Obviously, the lower the bulk oil temperature, the lower the interfacial temperature should be. Use contacting metals that are insoluble in each other: Because adhesive wear is a microwelding process, it follows that if two metals are not weldable...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.pb.t51230221
EISBN: 978-1-62708-351-5
... from thermal expansion mismatch is an important factor that must always be taken into consideration. On the other hand, most nonmetals are stable in chemical environments and have much higher elastic moduli and wear resistance than metals. Ashby plots provide a convenient method of comparing...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870537
EISBN: 978-1-62708-314-0
... to their base metals, such as higher specific strengths and moduli, higher elevated-temperature resistance, lower coefficients of thermal expansion, and, in some cases, better wear resistance. However, due to their high cost, commercial applications for MMCs are few. There are some limited uses...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350231
EISBN: 978-1-62708-315-7
... Abstract This chapter is a compilation of terms and definitions related to surface engineering for corrosion and wear resistance. corrosion resistance surface treatment wear resistance Surface Engineering for Corrosion and Wear Resistance Copyright © 2001 ASM International® J.R...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.9781627083157
EISBN: 978-1-62708-315-7
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870573
EISBN: 978-1-62708-314-0
... Abstract This chapter discusses the types of fibers and matrix materials used in ceramic matrix composites and the role of interfacial coatings. It describes the methods used to produce ceramic composites, including powder processing, slurry infiltration and consolidation, polymer infiltration...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610461
EISBN: 978-1-62708-303-4
... of transmission oil coolers in racing cars. Obviously, the lower the bulk oil temperature, the lower the interfacial temperature should be. Use contacting metals that are insoluble in each other. Because adhesive wear is a microwelding process, it follows that if two metals are not weldable to each other...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 September 2023
DOI: 10.31399/asm.tb.stmflw.t59390039
EISBN: 978-1-62708-459-8
... Abstract This chapter covers the different types of wear encountered in metalworking processes. It discusses the mechanisms involved in adhesive, abrasive, chemical, and fatigue wear and key contributing factors, including the composition and structure of tool and workpiece materials...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 September 2023
DOI: 10.31399/asm.tb.stmflw.9781627084598
EISBN: 978-1-62708-459-8
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350043
EISBN: 978-1-62708-315-7
... of engineering materials and coatings. It also describes the causes and effects of the most common forms of wear, the conditions under which they occur, the role of lubrication, and wear testing methods. friction coefficient lubrication wear wear testing FRICTION, WEAR, AND LUBRICATION are complex...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550511
EISBN: 978-1-62708-307-2
..., burner nozzles, heat exchanger heating elements, noniron metallurgy insulating parts, thermal barrier coatings Mechanical Long-term, high-temperature resistance; fatigue, thermal shock, wear resistance Wear parts; sealings; bearings; cutting tools; engine, motor, and gas turbine parts; thermal...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350125
EISBN: 978-1-62708-315-7
... Abstract This chapter discusses the use of coating methods and materials and their impact on corrosion and wear behaviors. It provides detailed engineering information on a wide range of processes, including organic, ceramic, and hot dip coating, metal plating and cladding, and the use of weld...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2005
DOI: 10.31399/asm.tb.gmpm.t51250257
EISBN: 978-1-62708-345-4
... of various fatigue failures. Then, it provides information on the modes of impact fractures, wear, scuffing, and stress rupture. Next, the chapter describes the causes of gear failures and discusses the processes involved in conducting the failure analysis. Finally, the chapter presents examples of gear...