This chapter gives an overview of how steel castings may be effectively adapted to modern concurrent engineering processes. The chapter discusses computer aided design programs, solid modeling, solidification simulation programs, and rapid prototyping.

Cold spray is a process technology that, for the first time, enables the rapid deposition of a wide range of metals and some other materials in the solid state at temperatures far below their melting points. This chapter provides an overview of the processes involved in cold spray process technologies, namely high-pressure cold spray (HPCS) and low-pressure cold spray (LPCS), explaining differences of LPCS from HPCS. It summarizes the historical background of the cold spray process. The growing international interest in the cold spray process from the early 2000s is also reviewed.

It is well established that solidification behavior in the fusion zone controls the size and shape of grains, the extent of segregation, and the distribution of inclusions and defects such as porosity and hot cracks. Since the properties and integrity of the weld metal depend on the solidification behavior and the resulting microstructural characteristics, understanding weld pool solidification behavior is essential. This article provides a general introduction of key welding variables including solidification of the weld metal or fusion zone and microstructure of the weld and heat-affected zone. It discusses the effects of welding on microstructure and the causes and remedies of common welding flaws.

This chapter covers the different types of wear encountered in metalworking processes. It discusses the mechanisms involved in adhesive, abrasive, chemical, and fatigue wear and key contributing factors, including the composition and structure of tool and workpiece materials, the characteristics of contact surfaces, and loading forces imposed by the process. It describes the nature of metal transfer between tool and workpiece surfaces and the role of lubricants, coatings, and textures. It also discusses the use of wear maps, the effects of adhesion, and material-lubricant interactions.

Failure analysis of steel welds may be divided into three categories. They include failures due to design deficiencies, weld-related defects usually found during inspection, and failures in field service. This chapter emphasizes the failures due to various discontinuities in the steel weldment. These include poor workmanship, a variety of hydrogen-assisted cracking failures, stress-corrosion cracking, fatigue, and solidification cracking in steel welds. Hydrogen-assisted cracking can appear in four common forms, namely underbead or delayed cracking, weld metal fisheyes, ferrite vein cracking, and hydrogen-assisted reduced ductility.

Soldering and brazing represent one of several types of methods for joining solid materials. These methods may be classified as mechanical fastening, adhesive bonding, soldering and brazing, welding, and solid-state joining. This chapter summarizes the principal characteristics of these joining methods. It presents a comparison between solders and brazes. Further details on pressure welding and diffusion bonding are also provided. Key parameters of soldering are discussed, including surface energy and surface tension, wetting and contact angle, fluid flow, filler spreading characteristics, surface roughness of components, dissolution of parent materials and intermetallic growth, significance of the joint gap, and the strength of metals. The chapter also examines the principal aspects related to the design and application of soldering processes.

This chapter is intended to identify materials, processes, and designs that will lead to great advances in powder-binder forming technologies. It discusses some of the structures obtained through these advances in powder-binder technologies such as binder jetting and extrusion-based additive manufacturing, including bound-metal deposition and fused-filament fabrication: oxidation-resistant high-temperature alloys, anisotropic structures, submicrometer-scale structures, surface hard materials, and artist metallic clays. Some of the advances discussed include the developments in process involving plastics, emulsions, ceramics, and porous structures and foams. Improvements in the design processes have led to the development of functional structures, controlled porosity, and bioinspired structures.

This chapter presents several materials and processes related to soldering technology. It first provides information on lead-free solders, followed by sections devoted to flip-chip processes, diffusion soldering, and modeling. Scanning acoustic microscopy and fine-focus x-ray techniques are also discussed. The chapter describes several evaluation procedures and tests developed to measure solderability and standards for process calibration. The chapter also describes the characteristics of reinforced solders, amalgams used as solders, and other strategies to boost the strength of solders. Further, the chapter considers methods for quantifying the mechanical integrity of joints and predicting their dimensional stability under specified environmental conditions. It discusses the effects of rare earth elements on the properties of solders. The chapter concludes with information on advanced joint characterization techniques.

Brazing and soldering jointly represent one of several methods for joining solid materials. This chapter summarizes the principal characteristics of the various joining methods. It then discusses key parameters of brazing including surface energy and tension, wetting and contact angle, fluid flow, filler spreading characteristics, surface roughness of components, dissolution of parent materials, new phase formations, significance of the joint gap, and the strength of metals. The chapter also describes issues in processing aspects that must be considered when designing a joint, and the health, safety, and environmental aspects of brazing.

This chapter describes the properties and attributes of various classes of metalworking lubricants, including mineral oils; natural oils, fats, derivatives, and soaps; synthetic fluids (olefins, esters, polyglycols, ionic liquids); compounded lubricants (oils, greases, fats); aqueous lubricants (emulsions, synthetics, solutions); and a wide range of coatings and carriers. It also discusses solid-film lubricants (oxide films, polymer films, layer-lattice compounds) and environmental and safety concerns.

Discontinuities are interruptions in the desirable physical structure of a weld. This article describes the types of weld discontinuities that are characteristic of the principal welding processes. Discontinuities covered are metallurgical discontinuities, discontinuities associated with specialized welding processes, and base metal discontinuities. In addition, information on the common inspection methods used to detect these discontinuities is provided.

This chapter discusses the advantages, limitations, and applications of various aluminum casting processes, namely green sand casting process, air set or no-bake molding process, vacuum molding process, evaporative foam casting process, and die casting process. The processes covered also include gravity permanent molding, low-pressure permanent molding, counter pressure, squeeze casting, investment casting, rapid prototype casting, cast forge hybrid, and semisolid metal processes.

This chapter reviews the basic theory of lubrication in the context of metal forming applications. It discusses the rheological properties of fluids and their effect on fluid-film thickness at pressures, temperatures, and loading conditions typical of metal working processes. It describes the three lubrication regimes (boundary, mixed, and hydrodynamic) of a Stribeck curve and the forces that maintain surface separation. It also discusses mixed, elastohydrodynamic, plastohydrodynamic, and solid or semi-solid lubrication, the effects of starvation and frictional instabilities, and the role of elastic deflection and ultrasonic vibration.

This chapter covers the mechanics and tribology of sheet metalworking processes, including shearing, bending, spinning, stretching, deep drawing, ironing, and hydroforming. It explains how to determine friction, wear, and lubrication needs based on process forces, temperatures, and strains and the effects of strain hardening on workpiece materials. It presents test methods for evaluating process tribology, describes lubrication and wear control approaches, and discusses the factors, such as surface roughness, lubricant breakdown, and adhesion, that can lead to galling and other forms of wear. It also provides best practices for selecting, evaluating, and applying lubricants for specific materials, including steels, stainless steels, and aluminum and magnesium alloys.