Several hydraulic pumps that failed in service on a particular type of aircraft were received for analysis. Hydraulic testing was not an option, so the pumps were disassembled and their plungers and cylinders were cleaned and examined. Based on their observations, investigators concluded that cavitation erosion damaged the plungers, causing them to seize.

This article provides an overview of the most common micro-analytical technique in the failure analysis laboratory: energy dispersive X-ray spectroscopy (EDS). It discusses the general characteristics, advantages, and disadvantages of some of the X-ray detectors attached to the scanning electron microscope chamber including the lithium-drifted EDS detector, silicon drift detector (SDD), and wavelength dispersive X-ray detector. The article then provides information on qualitative and quantitative X-ray analysis programs followed by a discussion on EDS elemental mapping. The discussion includes a comparison of scanning transmission electron microscope-EDS elemental mapping and mapping with an SDD. A brief section is devoted to the discussion on the artifacts that occur during X-ray mapping.

The overall chemical composition of metals and alloys is most commonly determined by x-ray fluorescence (XRF) and optical emission spectroscopy (OES). High-temperature combustion and inert gas fusion methods are typically used to analyze dissolved gases (oxygen, nitrogen, and hydrogen) and, in some cases, carbon and sulfur in metals. This chapter discusses the operating principles of XRF, OES, combustion and inert gas fusion analysis, surface analysis, and scanning auger microprobe analysis. The details of equipment set-up used for chemical composition analysis as well as the capabilities of related techniques of these methods are also covered.

This chapter discusses the use of electron microscopy in metallographic analysis. It explains how electrons interact with metals and how these interactions can be harnessed to produce two- and three-dimensional images of metal surfaces and generate crystallographic and compositional data as well. It discusses the basic design and operating principles of scanning electron microscopes, transmission electron microscopes, and scanning transmission electron microscopes and how they are typically used. It describes the additional information contained in backscattered electrons and emitted x-rays and the methods used to access it, namely wavelength and energy dispersive spectroscopy and electron backscattering diffraction techniques. It also describes the role of focused ion beam milling in sample preparation and provides information on atom probes, atomic force microscopes, and laser scanning microscopes.

This appendix is a compilation of suggested analysis methods for suspected component failure causes.

This chapter describes some of the most effective tools for investigating boiler tube failures, including scanning electron microscopy, optical emission spectroscopy, atomic absorption spectroscopy, x-ray fluorescence spectroscopy, x-ray diffraction, and x-ray photoelectron spectroscopy. It explains how the tools work and what they reveal. It also covers the topic of image analysis and its application in the measurement of grain size, phase/volume fraction, delta ferrite and retained austenite, inclusion rating, depth of carburization/decarburization, scale thickness, pearlite banding, microhardness, and hardness profiles. The chapter concludes with a brief discussion on the effect of scaling and deposition and how to measure it.

One of the rotor bearings in an electric motor failed, producing excessive vibrate. The bearing was removed and disassembled, revealing craters and bruises on the inner ring raceway and balls along with evidence of melting and burning of metal. Scanning electron microscopy revealed metal particles near the craters, and energy-dispersive x-ray analysis showed that slivers recovered from the grease had the same composition as the bearing raceway and balls. Based on these observations, it was concluded that the bearing failed due to electrostatic discharge, which would have led to seizure if it continued. The report recommends the use of electrically conductive grease and proper grounding practices.

After the fault-tree, a failure-cause identification method has identified potential failure causes and the failure analysis team has prepared a failure mode assessment and assignment (FMA&A). The team knows specifically what to search for when examining components and subassemblies from the failed system. There are numerous techniques and technologies available for examining and analyzing components and subassemblies, which are categorized as follows: optical approaches, dimensional inspection and related approaches, nondestructive test approaches, mechanical and environmental approaches, and chemical and composition analysis for assessing material characteristics. This chapter is a detailed account of the working principle and the steps involved in these techniques and technologies.

As semiconductor feature sizes have shrunk, the technology needed to encapsulate modern integrated circuits has expanded. Due to the various industry changes, package failure analyses are becoming much more challenging; a systematic approach is therefore critical. This article proposes a package failure analysis flow for analyzing open and short failures. The flow begins with a review of data on how the device failed and how it was processed. Next, non-destructive techniques are performed to document the condition of the as-received units. The techniques discussed are external optical inspection, X-ray inspection, scanning acoustic microscopy, infrared (IR) microscopy, and electrical verification. The article discusses various fault isolation techniques to tackle the wide array of failure signatures, namely IR lock-in thermography, magnetic current imaging, time domain reflectometry, and electro-optical terahertz pulse reflectometry. The final step is the step-by-step inspection and deprocessing stage that begins once the defect has been imaged.

This article covers common techniques for surface characterization, including the modern scanning electron microscopy and methods for the chemical characterization of surfaces by Auger electron spectroscopy, X-ray photoelectron spectroscopy, and time-of-flight secondary ion mass spectrometry. The principles of surface analysis and some of the applications of the technique in polymer failure studies are also provided.

Several specialized instruments are available for the metallographer to use as tools to gather key information on the characteristics of the microstructure being analyzed. These include microscopes that use electrons as a source of illumination instead of light and x-ray diffraction equipment. This chapter describes how these instruments can be used to gather important information about a microstructure. The instruments covered include image analyzers, transmission electron microscopes, scanning electron microscopes, electron probe microanalyzers, scanning transmission electron microscopes, x-ray diffractometers, microhardness testers, and hot microhardness testers. A list of other instruments that are usually located in a research laboratory or specialized testing laboratory is also provided.