1-20 of 293 Search Results for

dilution

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 July 1997
Fig. 6 Welding Research Council 1992 diagram with expanded scale for dilution calculations, in which ferrite is calculated for type 410 stainless steel welded with E309-16 (refer to Example 1) More
Image
Published: 01 March 2001
Fig. 6 Effect of processing parameters on dilution with experimental data plotted for SAW process. Source: Ref 41 More
Image
Published: 01 November 2011
Fig. 10.1 Dilution in a dissimilar-metal welded joint. Source: Ref 10.1 More
Image
Published: 01 November 2007
Fig. 13.1 Corrosion rate of chromium-iron alloys in dilute nitric and sulfuric acids. Source: Ref 13.2 More
Image
Published: 01 June 1983
Figure 6.25 The low-temperature susceptibility of dilute Cu—Fe alloys ( Fickett, 1974 ). The slope increase at 93 ppm is assumed to be due to the beginnings of a ferromagnetic interaction. More
Image
Published: 01 July 2009
Fig. 18.4 Relationship between supercooling and cooling rate in beryllium and dilute beryllium alloys. °, Be; Δ, Be-1wt%Th; □, Be-1wt%Ge. Source: Crossley et al. 1959 More
Image
Published: 01 December 2006
Fig. 3 Schaeffler diagram showing predicted microstructures and minimum dilutions necessary to form martensite for A36 base metal and three austenitic filler metals. Source: Ref 2 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.pnfn.t65900031
EISBN: 978-1-62708-350-8
... on the compound zone. It explains how to control and calculate compound zone thickness. Compound zone thickness can be controlled by dilution, the two-stage Floe process, or by ion nitriding. The chapter describes the factors affecting surface case formation. carbon compound layer iron microstructure...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2006
DOI: 10.31399/asm.tb.cw.t51820169
EISBN: 978-1-62708-339-3
.... Its composition depends upon the compositions of the base metals; the filler metal, if used; and the relative dilutions of these. The weld metal composition is usually not uniform, particularly with multipass welds, and a composition gradient is likely to exist in the weld metal adjacent to each base...
Image
Published: 01 December 1999
(dilution 1:20) Soluble oil (dilution 1:20) Cross feed, in./pass 0.050 0.050 Table speed, ft/min 40 40 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.pnfn.t65900065
EISBN: 978-1-62708-350-8
... work with dilution techniques (see the later discussion in this chapter), Thomas Bell of the University of Liverpool began work in the early 1970s on dilution of the ammonia gas by hydrogen ( Ref 2 ). His objective was to establish the mechanism of compound layer formation and to determine how...
Image
Published: 01 March 2002
Fig. 4.2 The first macrograph of the microstructure of steel, Sorby’s 1864 macrograph of blister steel. Etched in very dilute nitric acid. 9× More
Image
Published: 01 July 2009
Fig. 13.9 Macro elastic limit (critical resolved shear stress, or CRSS) for prismatic slip of beryllium and dilute beryllium-copper alloys as a function of temperature. Source: Avotin et al. 1974 , 1975 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290279
EISBN: 978-1-62708-306-5
... (if used), and the relative dilutions of these. The weld metal composition is usually not uniform, particularly with multipass welds, and a composition gradient is likely to exist in the weld metal adjacent to each base metal. These solidification characteristics of the weld metal are also influenced...
Image
Published: 01 September 2008
Fig. 2 Large gear that cracked during grinding operations. Localized thermal gradients during grinding resulted in high residual stresses and eventual cracking. Temper etching (dilute nitric acid in water) revealed the presence of abusive grinding. More
Image
Published: 01 January 2000
Fig. 1 Poor (a) and good (b) designs for vessels used for mixing concentrated and dilute solutions. Poor design causes concentration and uneven mixing of incoming chemicals along the vessel wall (circled areas). Good design allows concentrated solutions to mix away from vessel walls. More
Image
Published: 01 December 1999
Grinding fluid Sulf oil Soluble oil (dilution 1:20) Dry More
Image
Published: 01 August 2018
distilled water. Dilute Part I in 100 ml hydrogen peroxide (30%) just before using.) Metallography by I. C. Abud, INT, Brazil. Courtesy of MRS Logística S.A., RJ, Brazil. More
Image
Published: 01 August 2018
morphology is similar to those observed in the solidification of austenitic castings with bad selection of chemical composition. (In this case, the weld metal composition was excessively changed by diluting the engineering steel in the lower part of the image, generating conditions favorable to cracking More
Image
Published: 01 January 2015
at 900 °C (1650 °F) for ½ h and water quenching. (c) Microstructure contains still less alpha than in (b) and more beta after heating at 925 °C (1700 °F) for 15 min, but the beta is now diluted and, after water quenching, alpha prime forms. (d) Partial phase diagram. Etchant: 10%HF-5%HNO 3 . Original More