1-20 of 147 Search Results for

diamond grinding

Sort by
Image
Published: 01 November 2019
Figure 11 Exposed die is thinned with a fine diamond grinding bit. The die surface is removed as the tool traverses the surface. Water is dispensed and suctioned simultaneously to keep a clear view of the process. More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2022
DOI: 10.31399/asm.tb.tstap.t56040076
EISBN: 978-1-62708-428-4
... Recipe 1 sample preparation example Step Cloth Abrasive Lubricant Speed, RPM Force per sample, N Time, minutes Planar grinding MD Piano 120 Bonded diamond Water 300 30 3 Fine grinding I MD Piano 220 Bonded diamond Water 300 20 3 Polishing I MD Largo 9 μm diamond...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2022
DOI: 10.31399/asm.tb.tstap.t56040030
EISBN: 978-1-62708-428-4
... be much higher than the thermal spray coating. A low- speed diamond cut-off wheel is the most suitable for processing of thermal spray coatings because it provides a clean cut with minimal sectioning damage to the coating. The typical grinding step required after sectioning with a low-speed diamond...
Image
Published: 01 December 1999
Fig. 8.9(a) Residual stresses in SAE 4340 steel (quenched and tempered, 50 HRC) after grinding with CBN and diamond. Source: Ref 14 Conventional grind Diamond RVG-W Borazon II Wheel speed, ft/min 6000 6000 Down feed, in./pass 0.001 0.001 Grinding fluid Soluble oil More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2022
DOI: 10.31399/asm.tb.tstap.9781627084284
EISBN: 978-1-62708-428-4
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.omfrc.t53030043
EISBN: 978-1-62708-349-2
..., the final sample quality should be the same. In addition to the new equipment, new grinding and polishing disks that can last through the production of thousands of specimens are available and becoming standard in most laboratories that process many samples. These diamond-coated disks, either continuous...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1984
DOI: 10.31399/asm.tb.mpp.t67850060
EISBN: 978-1-62708-260-0
... Abstract This chapter explains how to prepare metallographic samples for light microscopy and how to anticipate and avoid related problems. It describes standard practices and procedures for sectioning, mounting, grinding, and polishing and identifies common defects along with their causes...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110391
EISBN: 978-1-62708-247-1
... sandpaper. Films (usually referred to as “lapping” films) have the grinding particles on a thin mylar sheet. The particles on this film can be either SiC, diamond, or aluminum oxide. For a given grit size, films will give a smoother finish with less damage than paper, because the film will be flatter than...
Image
Published: 01 June 2022
Figure 11 Surface finish after grinding steps. (a) Following P220 resin-bonded diamond disk grinding. (b) Following 9 μm fine grinding. More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.omfrc.t53030067
EISBN: 978-1-62708-349-2
... Grinding and Polishing.” The rough grinding process is best performed using silicon carbide papers. The successive reduction in grit size is the same as described in Chapter 3 . While diamond-bonded disks can also be used, they are not recommended, because hybrid materials tend to damage the disks...
Image
Published: 30 September 2023
Figure 13.56: Effects of carbide-forming elements on grinding ratio in grinding of various steels with diamond wheels. More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2002
DOI: 10.31399/asm.tb.mgppis.t60400169
EISBN: 978-1-62708-258-7
... can reveal different microstructural features if polished longitudinal, transverse, planar, or in some other orientation. Contamination of the specimen can easily take place during sectioning, grinding, and polishing by the accumulation of debris; for example, silicon carbide, diamond, or aluminum...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2022
DOI: 10.31399/asm.tb.tstap.t56040055
EISBN: 978-1-62708-428-4
...–9 μm diamond Fine grinding, 4–7 20–25 4.5–5.6 100–150 Comp No/lownap cloth Lapping oil or extending fluid 3 μm diamond Rough polishing, 1–3 20–30 4.5–6.7 100–150 Comp Synthetic suede Water (e) Colloidal silica Final polishing, 1–3 23–35 5.2–7.9 100–150 Contra (f...
Image
Published: 01 September 2005
, mm (in.) 349 (13¾) OD Form Diamond dressed Operating conditions Machine Gear grinding, rack type Speed, at 1850 rev/min, m/min (sfm) 2030 (6650) Infeed per pass  Roughing, mm (in.) 0.030 (0.0012)  Finishing, mm (in.) 0.020 (0.0008) Axial feed  Roughing, mm More
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 September 2023
DOI: 10.31399/asm.tb.stmflw.t59390456
EISBN: 978-1-62708-459-8
... discusses the mechanics and tribology of surface grinding and other forms of abrasive machining. chip formation crater wear cutting fluids cutting force cutting speed cutting tool materials cutting tool wear flank wear grinding grinding fluids lubrication machining metal removal milling...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230199
EISBN: 978-1-62708-298-3
... Abstract This chapter explains how to safely prepare beryllium alloy samples for metallographic analysis. It describes grinding, polishing, and etching procedures in detail. It also discusses the identification of major and minor constituents and the general appearance of beryllium...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 April 2013
DOI: 10.31399/asm.tb.imub.t53720161
EISBN: 978-1-62708-305-8
... for polishing with diamond abrasives, rather than softer cloths, such as canvas, billiard, and felt, maintains flatness. Final polishing using low nap cloths for short times introduces very little rounding compared to use of higher nap, softer cloths. Grinding Grinding should commence with the finest...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1984
DOI: 10.31399/asm.tb.mpp.t67850552
EISBN: 978-1-62708-260-0
... (Beaujard). Grind through 600-grit SiC. Immerse sample for 5 min at 20°C (Marshall). Prepolish sample through 6-(j.m diamond. Swab with fresh solution at 20-25°C for 4-10 s. Flush immediately with cold water (Christ and Smith). 3mLHF 97 mL H 2 0 2 (30%) Adjust HF concentration to obtain gas evolution. Good...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2022
DOI: 10.31399/asm.tb.tstap.t56040069
EISBN: 978-1-62708-428-4
... improvement in the viscosity of the epoxy. As with the preparation for all thermal spray coatings, sufficient material must be removed during the planar grinding stage to ensure that all sectioning damage has been removed. While all laboratories indicated a planar grinding step, one laboratory went as far...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.tb.msisep.t59220069
EISBN: 978-1-62708-259-4
... Titanium alloy, manual (b) Polishing until R a , μm 1200 grit grinding paper 0.130 6 μm diamond paste 0.125 3 μm diamond paste 0.060 0.7 μm diamond paste 0.056 Note: Values are only for reference. (a) Source: Adapted from Ref 3 . (b) Source: Adapted from Ref 4...