1-20 of 1503 Search Results for

cross-sectioning

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110391
EISBN: 978-1-62708-247-1
... Abstract Cross-sectioning is a technique used for process development and reverse engineering. This article introduces novice analysts to the methods of cross-sectioning semiconductor devices and provides a refresher for the more experienced analysts. Topics covered include encapsulated (potted...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110402
EISBN: 978-1-62708-247-1
... Abstract Cross-sectioning refers to the process of exposing the internal layers and printed devices below the surface by cleaving through the wafer. This article discusses in detail the steps involved in common cross-sectioning methods. These include sample preparation, scribing, indenting...
Image
Published: 01 November 2019
Figure 7 Failure site after cross sectioning by FIB again inspected by SEM [4] . More
Image
Published: 01 November 2019
Fig 14 Drawing of oxide VCSEL prepared by FIB for cross-sectioning (top) or plan-view imaging (bottom). Plan view image shows DLD network originating from the etch hole and traveling into emitting area. More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2016
DOI: 10.31399/asm.tb.ascaam.t59190147
EISBN: 978-1-62708-296-9
... in chemical composition. cast aluminum-silicon alloys etching intermetallic phase microstructure phase constituents 4.1 Visual Attributes of the Intermetallic Phase Precipitates in Aluminum Alloy Microstructure MICROSCOPIC OBSERVATION of metallographic cross sections allows...
Image
Published: 01 November 2019
Figure 12 Typical cross-section created by FIB milling. A polished cross-section is flanked at the sides by material re-deposition. More
Image
Published: 01 November 2019
Figure 27 2 cross sections performed using the PFIB. The first cross section on the left is to look for cracks in the underfill and the second cross section is to verify the solder bump connection. A low mag overview image shows cracks in the underfill and the solder bumps More
Image
Published: 01 December 2006
Fig. 2.15 (a) Carriage shell cross section ICE2 and (b) carriage shell cross section ICE3, self-supporting using welded large section technology. Source: ADtranz More
Image
Published: 01 November 2010
Fig. 1.11 Cross sections of interlayer-modified composite materials. (a) Cross section showing a middle ply at 90°. Bright-field illumination, 10× objective. (b) Cross section taken parallel to the fiber direction. Bright-field illumination, 10× objective More
Image
Published: 01 November 2010
Fig. 1.10 Cross section of a cross-plied carbon/epoxy laminate More
Image
Published: 01 June 1985
Fig. 3-8. Cross-sectional hardness survey through the splined section of a spiral bevel pinion shank. First readings at the surface (O.D. of the sample). Continuous readings at 1/16-in. intervals starting 1/16 in. from the surface. More
Image
Published: 01 June 1985
Fig. 3-9. Cross-sectional hardness survey chart of splined section shown in Fig. 3-8 . More
Image
Published: 01 December 2006
Fig. 7.62 Influence of the mandrel cross section on the section exit speed. Source: Ames More
Image
Published: 01 September 2011
Fig. 4.10 Computer-aided design section drawing of an Aero boat mast cross section More
Image
Published: 01 December 2006
Fig. 2.52 Cross section of an 800 mm wide large section in the alloy AlMgSi0.5 for the production of fixing plates for pneumatic control elements. Source: Alusuisse More
Image
Published: 01 November 2010
Fig. 15.3 Cross section taken at the edge of the strike zone corresponding to section plane A in Fig. 15.1 . The micrographs are taken away from the main damage area to show the effects of interply arcing. A Kevlar stitch is shown between the carbon fibers. (a) Slightly uncrossed polarized More
Image
Published: 01 November 2023
Fig. 14 (a) 3D image at 50 μm/vox resolution. (b) Virtual cross-section slides from 1.5-hr FDK scan. (c) Virtual cross-section using DLHRR 22-min scan. Copyright 2022 IEEE ( Ref 12 ) More
Image
Published: 01 November 2023
Fig. 3 Cross section of VNAND device. Source: Courtesy of TechInsights More
Image
Published: 30 November 2023
Fig. 3.16 (a) Roller conveyor for molds. (b) Roller cross-section details More
Image
Published: 30 November 2023
Fig. 3.20 (a) Platen underside showing casters. (b) Caster cross section More