1-20 of 897 Search Results for

crack size

Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540379
EISBN: 978-1-62708-309-6
... and appears to have considerable merit in estimating the total fatigue life of notched and cracked structures. damage rate fatigue crack initiation fatigue crack propagation fatigue life nonarbitrary crack size LOW-CYCLE FATIGUE CONCEPTS based on the local stress-strain approach have been...
Image
Published: 01 December 1989
Fig. 3.33. Remaining life as a function of initial crack size for an internally pressurized cylinder, illustrating a typical output from crack-growth analysis ( Ref 120 ). More
Image
Published: 01 December 1989
Fig. 5.47. Predicted crack size as a function of time for an internally pressurized cylinder (p = 13.79 MPa, or 2000 psi) ( Ref 73 ). More
Image
Published: 01 December 1989
Fig. 5.48. Remaining life as a function of initial crack size for an internally pressurized cylinder ( Ref 73 ). More
Image
Published: 01 July 1997
Fig. 5 Assessment procedures to determine limiting crack size More
Image
Published: 01 December 1995
Fig. 6-27 Critical crack sizes for linkage arm problem of Figure 6-12 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090359
EISBN: 978-1-62708-266-2
... SCC detection and sizing in stainless steel piping systems include the introduction of special transducers for intergranular SCC detection, the use of advanced sizing techniques based on crack-tip diffraction, and the increased level of personnel training and qualification. In addition, a number...
Image
Published: 01 January 2017
Fig. 16.5 Measuring the size of a crack larger than the beam diameter using the amplitude-drop technique More
Image
Published: 01 January 2017
Fig. 16.6 Measuring the size of a crack smaller than the beam diameter using the amplitude-drop technique More
Image
Published: 01 March 2002
Fig. 9.13 Total crack length of microfissures in IN-718 plotted against grain size, showing that increased grain size leads to more cracking (microfissuring) More
Image
Published: 01 March 2002
Fig. 12.40 Influence of γ′ size on cyclic crack growth rate of Waspaloy nickel-base superalloy at 649 °C (1200 °F) More
Image
Published: 01 March 2002
Fig. 12.41 Effect of grain size on fatigue crack growth rate of AP-1 nickel-base superalloy at room temperature More
Image
Published: 01 March 2002
Fig. 12.42 Effect of grain size on fatigue crack growth rate of P/M Astroloy at 649 °C (1200 °F) More
Image
Published: 01 November 2012
Fig. 56 Influence of grain size on fatigue crack growth at R = 0.07 for commercially pure titanium (CP Ti) with varying oxygen contents. Under these loading conditions, fatigue crack growth is lowered by coarse grains and increased oxygen content. Source: Ref 38 More
Image
Published: 01 January 1998
Fig. 7-4 Quench crack severity as a function of grain size for carbon tool steel austenitized at two temperatures. Source: Ref 8 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610303
EISBN: 978-1-62708-303-4
... Abstract Fracture control can be defined as a concerted effort to maintain operating safety without catastrophic failure by fracture. It requires an understanding of how cracks affect structural integrity and strength and the time that a crack can grow before it exceeds permissible size...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.tb.msisep.t59220039
EISBN: 978-1-62708-259-4
... Abstract This chapter discusses the practices and procedures used to reveal and record macrostructural features such as hardening depth, weld thickness, crack size, porosity, hot folds, and machining and tooling marks. It provides information on sectioning, sample location, orientation, surface...
Image
Published: 01 November 2012
Fig. 12 American Society of Mechanical Engineers (ASME) requirements for (a) permissible crack size ( a p ) for upset condition (where K ar is arrest toughness), (b) crack growth for upset condition (I = inspection interval), (c) permissible crack size for emergency condition, and (d More
Image
Published: 01 January 2017
Fig. 16.2 Comparison of sizing results obtained with crack-tip-diffraction and amplitude-drop sizing techniques. Source: Ref 16.10 More
Image
Published: 01 August 2005
Fig. 6.12 Crack-tip deformation zone sizes for Inco 718 at 593 °C (1110 °F) More