1-20 of 108 Search Results for

concrete

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 August 2018
Fig. 12.35 Longitudinal cross section of a reinforcing bar (rebar) for concrete made to 600 MPa (87 ksi) minimum yield strength specification, with 6 mm (0.25 in.) diameter, lightly work hardened during wire drawing (reduction of 30%). Pearlite and ferrite. Along the longitudinal section More
Image
Published: 01 January 2000
Fig. 12 Schematic of the cathodic protection of steel reinforcing bars in concrete. Arrows indicate current to the steel. More
Image
Published: 01 September 2008
Fig. 16 AISI W1 (0.85% C) tool steel concrete roughers that failed after short service (2 min for S, 7 min for S11). Failures occur at the change of sections. Source: Ref 16 More
Image
Published: 01 August 2013
Fig. 8.13 Concrete consists of gravel particles (large open circles), sand (small gray circles), and cement paste filling the remaining space. Source: Ref 8.2 More
Image
Published: 30 April 2021
Fig. 4.3 Water droplet erosion of concrete sidewalk in the drip line of a large roof without gutters More
Image
Published: 01 December 1995
Fig. 2-62 Cast steel flapper valve housing for use on a mobile concrete pump. Note light wall thickness achieved by strategic placement of ribs and integrally cast flanges More
Image
Published: 01 June 1983
Figure 12.42 Effect of low temperatures on the strength of moist concrete using various cement contents (bags per cubic yard gravel; 1 cu yd = 0.765 m 3 ) and for lightweight, expanded shale concrete ( Monfore and Lentz, 1962 ). More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910407
EISBN: 978-1-62708-250-1
... in concrete). The method has been used for more than 175 years and is applicable to virtually all metals, although it is primarily used for steel. Common applications include protection from soil corrosion (e.g., underground pipelines) and marine corrosion (pipelines, ship hulls, and offshore drilling...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2013
DOI: 10.31399/asm.tb.ems.t53730081
EISBN: 978-1-62708-283-9
... Abstract This chapter discusses the composition, properties, and uses of crystalline ceramics, glasses, clay, and concrete mixes. It also discusses the carbon structure of diamond, graphite, fullerenes, and nanotubes. amorphous carbon clay concrete mixes crystalline ceramics diamond...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2018
DOI: 10.31399/asm.tb.msisep.t59220475
EISBN: 978-1-62708-259-4
... and contrasts steels used for concrete reinforcement and in various types of pressure vessels, and presents a metallographic study of the effects of welding on the micro and macrostructure of steel. pressure vessels structural steel welding rebar The classification “structural steels” basically...
Book Chapter

By M. B. Kasen
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 1983
DOI: 10.31399/asm.tb.mlt.t62860413
EISBN: 978-1-62708-348-5
.... Figure 12.2 Cryogenic structural composite system flow chart. Figure 12.3 The conventional notation for uniaxial (a) and crossply (b) laminates. The crossply laminate is designated [0/±45/0] T . Figure 12.42 Effect of low temperatures on the strength of moist concrete using various...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.t52310213
EISBN: 978-1-62708-286-0
... factors pertinent to important considerations in buildings, namely surface finish aesthetics, flatness, maintenance, repair, fabrication, and service considerations. It ends with a section providing information on concrete reinforcing bar. stainless steel construction corrosion resistance...
Image
Published: 01 June 1983
Figure 3.23 Thermal expansion vs. temperature for some typical composites: 1) polyamide/epoxy, 2) boron/aluminum, 3) concrete, 4) fiberglass/epoxy (NEMA G-10CR), and 5) fiberglass/TFE. More
Image
Published: 01 March 2001
Fig. 1 Schematic of a chemical-resistant dual-lining system that provides double protection to the substrate in the form of a flexible membrane and a rigid surface layer. The flexible, corrosion-resistant membrane is applied in direct contact with steel or concrete substrates More
Image
Published: 01 January 2000
Fig. 14 Schematic of a chemical-resistant dual-lining system that provides double protection to the substrate in the form of a flexible membrane and a rigid surface layer. The flexible, corrosion-resistant membrane is applied in direct contact with steel or concrete substrates More
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2010
DOI: 10.31399/asm.tb.hss.t52790171
EISBN: 978-1-62708-356-0
... would be the tallest monument in the world, except for the Eiffel Tower. Saarinen designed an arch that would be 590 feet tall, almost 40 feet taller than the Washington Monument. It would be built of steel and concrete and faced with 426 stainless steel plates. The stainless steel would weigh 886 tons...
Image
Published: 01 January 2000
at the bottom of the member allows liquid to run off, rather than impinging directly on the concrete support. (i) Continuous welding is necessary for horizontal stiffeners to prevent the formation of traps and crevices. (j) Square sections formed from two L-shaped members require continuous welding to seal out More
Image
Published: 01 August 1999
of the member allows liquid to run off, rather than impinge directly on the concrete support. (i) Continuous weld for horizontal stiffeners prevents traps and crevices from forming. (j) Square sections formed from two L-shape members need to be continuously welded to seal out the external environment. More
Image
Published: 01 August 1999
of the member allows liquid to run off, rather than impinge directly on the concrete support. (i) Continuous weld for horizontal stiffeners prevents traps and crevices from forming. (j) Square sections formed from two L-shape members need to be continuously welded to seal out the external environment. More
Image
Published: 01 December 2015
liquid to run off, rather than impinge directly on the concrete support. (i) Continuous weld for horizontal stiffeners prevents traps and crevices from forming. (j) Square sections formed from two L-shape members need to be continuously welded to seal out the external environment. More