Two compressor rotors of similar design and construction were severely damaged during operation. In one rotor, all the blades in the third and fourth stages had been sheared off and some had lifted from the dovetail portion of the drum. The damage in the other rotor was more extensive. Most of the blades in the first four stages had sheared off and many lifted from the dovetail region, particularly in the first two stages where several mounting dovetails had also fractured. Based on visual examination and the results of SEM fractography, metallography, and chemical analysis, investigators concluded that the compressor rotors failed due to stress-corrosion cracking in the dovetail mountings. They also provided recommendations to prevent or mitigate future occurrences.

This report describes the failure of a gas turbine in a combined-cycle power plant and the examination and tests that were conducted to determine the cause. Based on microstructural analysis, hardness measurements, and tensile tests, the failure was attributed to inadequate clearances in the seal land region between two stages in the compressor section of the rotor. The report also recommends changes to remediate the problem.

This chapter discusses some of the promising developments in the use of titanium, including titanium aluminides, titanium matrix composites, superplastic forming, spray forming, nanotechnology, and rapid solidification rate processing. It also reports on efforts to increase the operating temperature range of conventional titanium alloys and reduce costs.

This chapter begins with information on the historical development of aluminum alloy castings. It then covers the basic factors involved in the selection of a casting process. This is followed by sections describing the various categories of casting processes and their variants: expendable mold gravity-feed casting, nonexpendable (permanent) mold gravity feed casting, and pressure die casting. Next, the chapter describes the technologies used to produce premium engineered castings and when such castings may be relevant. The chapter concludes with descriptions of other process technologies used with castings, including metallurgical bonding, metal-matrix composites, and hot isostatic pressing.

This appendix provides detailed information on design deficiencies, material and manufacturing defects, and service-life anomalies. It covers ingot-related defects, forging and sheet forming imperfections, casting defects, heat treating defects, and weld discontinuities. It shows how application life is affected by the severity of service conditions and discusses the consequences of using inappropriate materials.

This chapter discusses the crystal structures of steel and cast iron, the iron-iron carbide equilibrium diagram, microconstituents or phases in the iron-iron carbide phase diagram, the iron-carbon carbide-silicon equilibrium diagram of cast irons, and the influence on microstructure by base elements and alloying elements. Graphitization, cooling rates, and heat treatment effects are covered. There also is discussion on inoculation benefits, flake graphite types and typical applications, evolution of cast iron types, ASTM specification A247 for graphite shapes, and selection of the best molding process. A large table lists typical material choices for various applications.

This chapter covers mechanical properties, microstructures, chemical compositions, manufacturing processes, and engineering of gating practices for several applications of gray, white, and alloyed cast irons. It begins with a description of material standards, followed by a section providing information on the practice of stress relieving. Next, the chapter details various ways of eliminating slag entrainment while designing gating and venting systems. Several factors related to the establishment of the optimum pouring rate and time are then covered. Further, the chapter discusses the technology of unalloyed or low-alloyed gray iron castings and white iron and high-alloyed cast irons. Finally, it describes the casting defects that are associated with cast iron and the processes involved in solving these defects. The article includes a number of figures illustrating the topics discussed.

Steel castings are produced in thousands of designs for different applications. They fill needs in many industries, including transportation, construction machinery, earthmoving equipment, rolling mills, mining, oil and gas exploration, and power generation. This chapter touches upon the variety of applications for which steel castings can be supplied and the ranges of casting size and complexity. Photographs in this chapter provide an understanding of these applications, their size and complexity, and the types of cast steels produced.

Ductile iron has far superior mechanical properties compared to gray iron as well as significantly improved castability and attractive cost savings compared to cast steel. This chapter begins with information on graphite morphology and matrix type. It then discusses the advantages and applications of ductile iron. Next, the effects of various factors on the grades, chemistry, matrix, and mechanical properties of ductile iron are covered. This is followed by a section detailing the ductile iron treatment methods and the quality control methods used. Guidelines for gating and feeder design are then provided. Further, the chapter addresses the technology of ductile iron castings, including the performance and geometric attributes, molding and core-making processes used, material grades, mechanical properties, and chemical compositions of a few applications. Finally, it describes ductile iron casting defects and presents practical cases of problem-solving.

This chapter provides a brief overview of nickel-iron-base, cobalt-base, and nickel-base superalloys, discussing their basic metallurgy and defining characteristics.

This appendix provides composition data and application-related information on a wide range of superalloys in both wrought and cast form.

This chapter provides an overview of the possible mechanisms of failure for heat treated steel components and discusses the techniques for examining fractures, ductile and brittle failures, intergranular failure mechanisms, and fatigue. It begins with a description of the general sources of component failure. This is followed by a section on the stages of a failure analysis, which can proceed one after the other or occur at the same time. These stages of analysis are collection of background data, preliminary visual examination, nondestructive testing, selection and preservation of specimens, mechanical testing, macroexamination, microexamination, metallographic examination, determination of the fracture mechanism, chemical analysis, exemplar testing, and analysis and writing the report. The chapter ends with a discussion on various processes involved in the determination of the fracture mechanism.

Aluminum casting alloy compositions parallel those of wrought alloys in many respects. However, because work hardening plays no significant role in the development of casting properties, the use and purposes of some alloying elements differ in casting alloys versus wrought alloys. This chapter provides information on specifications and widely used designation systems and alloy nomenclature for aluminum casting alloys. It describes the composition of seven basic families of aluminum casting alloys: aluminum-copper, aluminum-silicon-copper, aluminum-silicon, aluminum-silicon-magnesium, aluminum-magnesium, aluminum-zinc-magnesium, and aluminum-tin. The chapter discusses the effects of alloying elements on the properties of cast aluminum. It provides information on various alloys that are grouped with respect to their applications or major performance characteristics.

Titanium is a lightweight metal with a density approximately 60% that of steel and, through alloying and deformation processing, it can be just as strong. It is readily available in many grades and forms and can be further processed using standard methods and techniques. This chapter provides a concise review of the capabilities of titanium and its design advantages over other materials. It includes information on properties and selection factors as well as applications.

This chapter is a collection of tables listing: cast alloy designations of Aluminum Association, along with their general applications; the chemical compositions of the frequently used alloys for gravity permanent molds, low-pressure permanent molds, squeeze castings, and die castings; the typical tensile properties of die cast alloys; and the designations of different heat treatments and their description. The tables also list the temperatures and times of typical heat treatment cycles for different permanent mold cast alloys; typical components in sand, gravity, and low-pressure permanent mold castings and die castings, the functional requirements of each process, and the corresponding suitable alloys and heat treatments; and alloys that are high vacuum die cast for structural castings. The chapter also presents examples of photomicrographs of some alloys cast by different processes.

Aluminum is the second most widely used metal in the world. It is readily available, offers a wide range of properties, and can be shaped, coated, and joined using a variety of methods. This chapter discusses some of the key attributes of wrought and cast aluminum alloys and the classifications, designations, and grades of available product forms. It also explains how aluminum alloys are used in aerospace, automotive, rail, and marine applications as well as in building and construction, electrical products, manufacturing equipment, packaging, and consumer durables such as appliances and furniture.