1-20 of 924 Search Results for

composites testing

Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.tt2.t51060163
EISBN: 978-1-62708-355-3
... Abstract This chapter describes tensile testing of advanced ceramic materials, a category that includes both noncomposite, or monolithic, ceramics and ceramic-matrix composites (CMCs). The chapter presents four key considerations that must be considered when carrying out tensile tests...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.tt2.t51060183
EISBN: 978-1-62708-355-3
... Abstract This chapter presents the fundamentals of tensile testing of fiber-reinforced polymer composites. Basic tensile testing of polymer composites is divided into lamina and laminate testing. The chapter focuses on tensile testing of laminates. It discusses the most common tensile test...
Image
Published: 01 August 2005
Fig. 8.48 Building-block pyramid for testing of composites. Source: Ref 8.56 More
Image
Published: 01 December 2004
Fig. 3 Specimen for tensile testing of composites as defined in ASTM D 3039. L g = gage length; L T = tab length; L τ = tab bevel angle; W width. Note: the gage length is commonly 125 to 150 mm (5 to 6 in.). More
Image
Published: 31 March 2024
Fig. 1.32 Composite tests, (a) double-flank test measures variation in center distance, and (b) single-flank test measures rotational movements More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2011
DOI: 10.31399/asm.tb.cfw.t52860095
EISBN: 978-1-62708-338-6
... Abstract The objective of mechanical testing of an engineered material is to provide data necessary for the analysis, design, and fabrication of structural components using the material. The testing of filament-wound composite materials offers unique challenges because of the special...
Image
Published: 01 September 2011
Fig. 8.3 Test specimens and test techniques for filament-wound composites. Source: Ref 8.16 More
Image
Published: 01 November 2010
Fig. 13.17 Typical composite materials fracture toughness tests More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870351
EISBN: 978-1-62708-314-0
... Abstract This chapter discusses composite testing procedures, including tension, compression, shear, flexure, and fracture toughness testing as well as adhesive shear, peel, and honeycomb flatwise tension testing. It also discusses specimen preparation, environmental conditioning, and data...
Image
Published: 01 December 2003
Fig. 24 Chop marks on the fracture surface of the glass fibers in a glass/polyimide composite tested as a notched four-point bend specimen that failed in compression. 1800× More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780417
EISBN: 978-1-62708-281-5
... manufactured from different composite materials under different processes and exposed to different environmental and load conditions. The fracture surfaces of the pedigreed test specimens are examined, documented, and analyzed to determine which features are specific to a particular material, process, load...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610377
EISBN: 978-1-62708-303-4
..., damage tolerance, and testing and certification. composite laminates continuous carbon-fiber composites continuous-fiber polymer-matrix composites damage tolerance fatigue failure mechanisms A COMPOSITE MATERIAL can be defined as a combination of two or more materials that results...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2011
DOI: 10.31399/asm.tb.cfw.t52860115
EISBN: 978-1-62708-338-6
... of the advantages of composites over metals for RMCs. A discussion on a typical design, analysis, and manufacturing operation follows. The chapter introduces the basic design approach and shows some sizing techniques along with example calculations. It discusses the processes involved in the testing...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2011
DOI: 10.31399/asm.tb.cfw.9781627083386
EISBN: 978-1-62708-338-6
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 1997
DOI: 10.31399/asm.tb.wip.t65930039
EISBN: 978-1-62708-359-1
..., specimens, or equipment for toughness testing; however, there are special problems for the testing of weldments that are not contained in the other standards. Weldments have a composite of materials starting in the base metal, going through the heat-affected zone and into the weld metal. Such things...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.omfrc.t53030223
EISBN: 978-1-62708-349-2
... systems, the prepreg matrix has self-adhesive characteristics that enable adequate skin-core bonds, while other prepreg systems require the use of a film adhesive to provide the necessary bond. Some common tests performed on honeycomb composites are climbing drum peel and flatwise tensile tests...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2020
DOI: 10.31399/asm.tb.bpapp.t59290193
EISBN: 978-1-62708-319-5
... procedure. Mechanical hardness and strength tabulations are provided to document sintered properties. mechanical properties performance test sintering Sintering produces a strong engineering component. Properties are dominated by composition, such as the high density associated with tungsten...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540319
EISBN: 978-1-62708-309-6
..., and numerous test data for this material are available in the literature. In this chapter, therefore, discussion is limited to those PMCs known as filamentary composites, which are made up of long continuous fibers (generally graphite or boron) embedded in a matrix of epoxy or thermoplastic. The stress...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.t69870325
EISBN: 978-1-62708-344-7
... and ceramic fiber-reinforced metal-matrix composites. bone cyclic loading ceramics fatigue crack growth fatigue modeling fatigue properties fatigue test polymers Introduction In this chapter we consider several classes of materials that are of special interest: polymers, bone, ceramics...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.tt2.t51060239
EISBN: 978-1-62708-355-3
... properties such as fatigue and interlaminar shear strength are sometimes questionable. Two good sources of properties of structural composites at low temperature are Ref 4 and 5 . Test Selection Factors: Tensile versus Compression Tests Tensile and compression tests produce engineering data...