1-20 of 941 Search Results for

cast metal

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 June 2008
Fig. 7.14 Porosity in cast metals. Source: Ref 8 More
Image
Published: 01 June 2008
Fig. 16.3 Relative workabilities of wrought and cast metals. Source: Ref 2 More
Image
Published: 01 October 2011
Fig. 6.9 Schematic illustration of relative workability of cast metals and wrought and recrystallized metals at cold, warm, and hot working temperatures. The melting point (or solidus temperature) is denoted as MP c (cast metals) or MP w (wrought and recrystallized metals). More
Image
Published: 01 March 2012
Fig. B.13 Porosity in cast metals. Source: Ref B.7 as published in Ref B.2 More
Image
Published: 01 November 2013
Fig. 3 Relative workabilities of wrought and cast metals. Source: Ref 3 More
Image
Published: 01 December 1995
Fig. 3-26 Comparison of tensile strength of cast metals as to the range possible for each metal More
Image
Published: 01 December 1995
Fig. 3-27 Comparison of the range of yield strengths for cast metals More
Image
Published: 01 December 1995
Fig. 3-29 Reduction of area range comparison of cast metals. Not applicable to aluminum, magnesium, or zinc alloys More
Image
Published: 01 December 1995
Fig. 3-30 Comparison of the range of hardness commercially found in cast metals More
Image
Published: 01 December 1995
Fig. 3-31 The Charpy V-notch impact property range of ferrous cast metals. Standard Charpy [0.394 in. (10 mm) bar with 45° notch 0.08 in. (2 mm) deep). Test too severe for nonferrous alloys More
Image
Published: 01 December 1995
Fig. 3-32 The elastic modulus of cast metals More
Image
Published: 01 December 1995
Fig. 3-33 Coercive force range of iron and nickel-base cast metals More
Image
Published: 01 June 2008
Fig. 25.8 As-cast Muntz metal. Original magnification: 210×. Source: Ref 4 More
Image
Published: 01 November 2007
Fig. 15.1 Corrosion rates in terms of metal loss for four commercial cast Fe-Ni-Cr alloys in a 20NaCl-25KCl-55BaCl 2 salt bath under different conditions of rectification at 870 °C (1600 °F) for 60 h. Source: Ref 6 More
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2013
DOI: 10.31399/asm.tb.mfub.t53740047
EISBN: 978-1-62708-308-9
... Abstract This chapter covers the practices and procedures used for shape casting metals and alloys. It begins with a review of the factors that influence solidification and contribute to the formation of casting defects. It then describes basic melting methods, including induction, cupola...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1995
DOI: 10.31399/asm.tb.sch6.t68200048
EISBN: 978-1-62708-354-6
... information on cast steel compared to other cast metals and other methods of steel fabrication. steel castings weldments wrought steel Introduction Steel is strong, steel is tough, steel is dependable! Casting steel to shape represents the most direct method of producing parts to final form...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.smnm.t52140165
EISBN: 978-1-62708-264-8
... Abstract Engineering metals undergo many transformations in the course of production, none more critical than those that occur during solidification. This chapter discusses the process of solidification and its effects on the structure and properties of cast metals. It describes...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060117
EISBN: 978-1-62708-261-7
... Abstract This chapter describes the processes involved in the fabrication of wrought and cast metal products. It discusses deformation processes including bending and forming, material removal processes such as milling, cutting, and grinding, and joining methods including welding, soldering...
Image
Published: 01 December 2006
Fig. 6.74 Mold casting system with constant-level metal feed from the casting launder. Source: VAW-Elbewerk, Stade More
Image
Published: 01 December 1995
Fig. 3-28 Comparison of the range of tensile elongation usual in commercial cast metals More