1-20 of 261 Search Results for

blending

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 August 2005
Fig. 2.35 Fracture model showing a cleavage step blending with a tear ridge in a quasi-cleavage fracture surface. At top left is the lower surface of a fracture, showing a step at the lower left and a ridge at the upper right. At right and at bottom are sections through the fractured member More
Image
Published: 01 June 2016
Fig. 2.15 Effect of geometrical conditions in cold spraying a powder blend of 50 vol% copper and 50 vol% tungsten particles (a, b) with coarse hard-phase particles in sizes of 22 to 45 μm and (c, d) fine hard particles in sizes of 5 to 15 μm. Cold spraying was performed with nitrogen More
Image
Published: 01 December 2003
Fig. 14 G ′ of polyvinyl chloride (PVC) blends; MW A = 58 × 10 4 ; MW B = 5.9 × 10 4 More
Image
Published: 01 December 2003
Fig. 27 Differential scanning calorimetry (DSC) of polyethylene/polypropylene blend 10 mcal/s range; 20 °C/min (36 °F/min). PE, polyethylene; PP, polypropylene. Source: Ref 29 More
Image
Published: 01 December 2003
Fig. 30 Thermogravimetric analysis (TGA) of acetal/fluorocarbon blend; 40 °C/min (70 °F/min) in air More
Image
Published: 01 January 2015
Fig. 8.21 Schematic processing sequence for production of Ti-6Al-4V foil from blended-elemental starting stock More
Image
Published: 01 January 2015
Fig. 8.22 Typical blended-elemental Ti-6Al-4V compact microstructures after cold pressing and sintering with some residual porosity. (a) Mechanically pressed. (b) Isostatically pressed. (c) After the “broken-up” structure heat treatment. (d) After thermohydrogen processing More
Image
Published: 01 January 2015
Fig. 8.23 Comparison of fatigue behavior of annealed blended-elemental and prealloyed Ti-6Al-4V powder metal compacts with ingot metallurgy material More
Image
Published: 01 January 2015
Fig. 8.26 Cold isostatically pressed blended-elemental Ti-6Al-4V impeller produced using an elastomeric mold. Courtesy of Dynamet Technology Inc. More
Image
Published: 01 January 2015
Fig. 8.27 Pressed-and-sintered blended-elemental Ti-6Al-4V connector link arm for the Pratt & Whitney F100 engine. Courtesy of Imperial Clevite Inc. More
Image
Published: 01 December 2000
Fig. 7.1 Aerospace and automotive Ti-6Al-4V parts produced using blended elemental powder. (a) Impeller. (b) F-18 pivot fitting. (c) Missile housing. (d) Lens housing. (e) Automotive cylinder More
Image
Published: 01 December 2000
Fig. 7.3 Impeller made from Ti-6Al-4V blended elemental powder. Courtesy of Dynamet Technology, Inc. More
Image
Published: 01 December 2000
Fig. 7.6 Typical tensile properties of blended elemental titanium alloy powder compacts. Shaded areas represent observed ranges. More
Image
Published: 01 December 2000
Fig. 7.7 Room-temperature smooth axial fatigue behavior of blended elemental and prealloyed powder metallurgy powder compacts of Ti-6Al-4V compared with wrought annealed material More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More
Image
Published: 01 December 1984
. Resin to hardener ratio incorrect. Correct resin to hardener ratio. Bubbles Too violent agitation while blending resin & hardener mixture. Blend mixture gently to avoid air entrapment. Discoloration Resin to hardener ratio incorrect. Correct resin to hardener ratio. Oxidized More