1-20 of 1230 Search Results for

alloy surface

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 2015
Fig. 24 Schematic of tubercle formed by bacteria on an aluminum alloy surface. Source: The Electrochemical Society More
Image
Published: 01 January 2015
Fig. 13.1 Typical alpha case on titanium alloy surface. Original magnification: 100×. Courtesy of Sikorsky Aircraft More
Image
Published: 01 August 1999
Fig. 13 Schematic of tubercule formed by bacteria on an aluminum alloy surface. Source: The Electrochemical Society More
Image
Published: 01 November 2007
Fig. 5.72 Typical surface conditions for (a) alloy 214 after 5707 h, (b) alloy HR120 after 190 h, and (c) alloy 800H after 925 h at 650 °C (1200 °F) in H 2 -49CO-2H 2 O ( a c = 18.9). Source: Ref 96 More
Image
Published: 01 November 2007
Fig. 3.18 Surface deletion of chromium near the surface of the plate of alloy AL-6XN (Fe-21Cr-24Ni-6.5Mo-0.2N) after annealing in air at 1120 and 1175 °C (2050 and 2150 °F), respectively. Source: Ref 29 More
Image
Published: 30 September 2023
Figure 8.17: SEM photograph of surface of annealed aluminum alloy 6061 strip rolled with bright stock lubricant (0.53 Ns/m 2 at 38°C) at 47% reduction and at a speed of 0.37 m/s. More
Image
Published: 01 January 2017
Fig. 13.4 (a) Fracture surface of amorphous Fe-10Cr-12Mo-18C alloy that failed by tensile testing at a strain rate of 5.9 × 10 −6 /s during galvanostatic cathodic polarization at 1 mA/cm 2 in 1 N H 2 SO 4 solution. (b) to (d) High magnification of the areas boxed in (a). Source: Ref 13.10 More
Image
Published: 01 January 2017
Fig. 13.5 Fracture surface of amorphous Fe-15Cr-12Mo-18C alloy that failed by tensile testing in 1 N HCl at a strain rate of 5.9 × 10 −6 /s. Source: Ref 13.2 More
Image
Published: 01 December 2015
Fig. 26 Effect of water vapor on the fracture surface appearance of aluminum alloy 2219-T851 fatigue tested (a) in 0.101 MPa (1 atm) dry argon and (b) in 27 Pa (0.2 torr) water vapor. Testing conditions were the same except for frequency, which was 20 Hz in (a) and 5 Hz in (b More
Image
Published: 01 August 2005
Fig. 2.38 SEM image of the fracture surface of a nickel-base alloy (Inconel 751, annealed and aged) after stress rupture (730 °C, or 1350 °F; 380 MPa, or 55 ksi; 125 h). (a) Low-magnification view, with picture width shown at approximately 0.35 mm (0.0138 in.) from original magnification More
Image
Published: 01 November 2007
Fig. 5.71 Optical micrographs showing typical surface conditions for (a) HR160 alloy, (b) alloy 230, and (c) alloy 601 after testing at 650 °C (1200 °F) for 10,000 h in H 2 -49CO-2H 2 O ( a c = 18.9). Magnification bar represents 20 μm for (a), 200 μm for (b) and (c). Source: Ref 96 More
Image
Published: 01 August 2005
Fig. 2.19 Liquidus surface of the copper-manganese-zinc ternary alloy phase diagram with the compositions of the 70Cu-20Zn-10Mn and 54Cu-35Zn-6Ni-4Mn-1Si brazes, shown as wt%. The light shaded area is the approximate location of brittle alloys. The two darker dots are braze compositions. More
Image
Published: 01 January 2015
Fig. 2.21 Liquidus surface of ternary alloy A, B, and C. Temperature, °F More
Image
Published: 01 November 2007
Fig. 7.35 Total surface recession including internal attack for alloy 625 at 330 to 700 °C (626 to 1292 °F) in CO-51.2H 2 -0.8CO 2 -1.7H 2 S-0.2HCl. Source: Ref 68 More
Image
Published: 01 November 2010
Fig. 5.9 Scanning electron micrographs of the fracture surface of alloy 706 due to stress-assisted grain-boundary oxidation after constant strainrate testing. (a) Brittle, intergranular fracture of unmodified alloy 706. (b) Transition zone of the boronized sample, showing a ductile More
Image
Published: 01 November 2012
Fig. 27 Effect of water vapor on the fracture surface appearance of aluminum alloy 2219-T851 fatigue tested (a) in 0.101 MPa (1 atm) dry argon and (b) in 27 Pa (0.2 torr) water vapor. Testing conditions were the same except for frequency, which was 20 Hz in (a) and 5 Hz in (b More
Image
Published: 01 December 1999
Fig. 1.8 Distribution of oxides at the surface of a Cr-Mn alloy steel carburized at 930 °C for 5 h. Adapted from Ref 6 , 7 More
Image
Published: 01 December 1999
Fig. 4.10 Influence of retained austenite on the surface hardness of carburized alloy steels. Reheat quenched and tempered at 150 to 185 °C More
Image