1-20 of 113 Search Results for

adhesive bonded joints

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.caaa.t67870161
EISBN: 978-1-62708-299-0
... have a lower resistance to corrosion than joints that are welded or brazed have. Adhesive bonding is widely used to join aluminum alloys to themselves, each other, other metals, and many nonmetals, including all forms of paper products, insulation board, wood-particle board, plaster board...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870449
EISBN: 978-1-62708-314-0
... Abstract This chapter discusses the use of mechanical fastening and adhesive bonding, the primary methods for joining polymer matrix composites. It describes and analyzes the basic types of mechanically fastened joints, including single-hole and multirow bolted composite joints. It then reviews...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290243
EISBN: 978-1-62708-306-5
... information on the theory of adhesion. The chapter then describes the considerations for designing adhesively bonded joints and for testing or characterizing adhesive materials. The following section covers the characteristics of the most important synthetic adhesive systems and five groups of adhesives...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290279
EISBN: 978-1-62708-306-5
... of these methods are covered. The factors influencing joint integrity and the main considerations in welding dissimilar metal combinations are also discussed. adhesive bonding brazing ceramics dissimilar metal welding mechanical fastening plastics welding A NUMBER OF materials and material...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230441
EISBN: 978-1-62708-298-3
... of different adhesives, and surface preparation requirements. It explains how adhesives are applied and cured and how curing times and temperatures affect bonding strength. It also discusses the use of bolts and rivets and the different types of joints that can be made with them. adhesive bonding...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870235
EISBN: 978-1-62708-314-0
... to other cured composites, honeycomb core, foam core, or metallic pieces. A number of possible adhesive bonding joint configurations are shown in Fig. 8.1 . The ability to make large bonded structures can eliminate a significant amount of the assembly costs. In addition to fabricating large bonded...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290001
EISBN: 978-1-62708-306-5
... loading the assembly will be exposed to during its service life. For example, in metallic structures, butt joints are preferred over tee, corner, lap, or edge joints for components subjected to fatigue loading, while a lap joint would be optimum for an adhesive-bonded structure. However, since high...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.tpmpa.t54480265
EISBN: 978-1-62708-318-8
... is not compatible with the heat treatment of the heat treatable alloys, the full potential of the alloy will not be used in brazed joints. As is true for all metals, proper surface preparation is critical in adhesive bonding operations. Surface treatments for titanium include cleaning and surface conditioning...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870183
EISBN: 978-1-62708-314-0
... plies. While a number of these surface preparations, or combinations of them, give acceptable bond strengths, the long-term service durability of thermoplastic adhesively bonded joints has not yet been established. Thermoplastic composites can be mechanically fastened in the same manner as thermoset...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870255
EISBN: 978-1-62708-314-0
... cocuring and adhesive bonding. As shown in the joint in Fig. 9.34 , a series of precured stiffeners are adhesive-bonded to a skin at the same time that the skin is cured. The surfaces of the precured composite parts must, of course, be prepared for adhesive bonding, just as in any other adhesive bonding...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870333
EISBN: 978-1-62708-314-0
... during curing, they normally result in either the need for a repair or scrapping of the part if the foreign object is large enough or located in a highly stressed area. The cure process can also result in defects, the most serious being porosity and voids. If an adhesive bonding operation is involved...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550141
EISBN: 978-1-62708-307-2
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.tb.sfa.t52780131
EISBN: 978-1-62708-268-6
.... Bond joints can be formed from epoxies, adhesives, or other sealants (such as room-temperature vulcanizing sealant). Potential epoxy-, adhesive-, and other sealant-leak causes include: Epoxies can be delivered in either a premixed, refrigerated configuration or in a two-part, unrefrigerated...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.tb.sfa.t52780109
EISBN: 978-1-62708-268-6
... specifications and monitoring. If all dimensions are in conformance and the bond joint fails, the bond design may be inadequate. The failure analysis team should consider checking with the epoxy manufacturer to identify recommended bond dimensions for anticipated loads and if the specified adhesive...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550385
EISBN: 978-1-62708-307-2
.... Composites offer the opportunity to significantly reduce the amount of assembly labor and fasteners. Detail parts can be combined into a single cured assembly, either during initial cure or by secondary adhesive bonding. Disadvantages of composites include high raw material costs and high fabrication...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870351
EISBN: 978-1-62708-314-0
... brittle, will often fail in interlaminar peel. In addition, the bondline is not long enough, typically the overlap is 0.5 in. (1.3 cm), to be representative of actual bonded joints. In spite of these shortcomings, the single lap shear test is used extensively for process control testing of adhesively...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550033
EISBN: 978-1-62708-307-2
..., and tanks requiring high weld efficiency and maximum joint strength. Used in pressure vessels up to 65 °C (150 °F) and in many cryogenic applications, bridges, freight cars, marine components, TV towers, drilling rigs, transportation equipment, missile components, and dump truck bodies. Good corrosion...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 1988
DOI: 10.31399/asm.tb.eihdca.t65220281
EISBN: 978-1-62708-341-6
... of induction heating in the area of joining include adhesive bonding and setting of metallic-particle gaskets. Adhesive bonding relies on the localized heating of a metallic substrate to achieve melting and curing of an adhesive. In a typical example, shafts are bonded directly to squirrel-cage rotors...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300079
EISBN: 978-1-62708-323-2
... materials. In summary, biotribology is applying the science of rubbing surfaces to systems in the human body. The wear mechanisms that prevail range from adhesive wear, metal-on-metal joints, plastic-on-metal joints; to abrasion such as toothpaste, abrasiveness of foods; to wear of soft tissue...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870489
EISBN: 978-1-62708-314-0
...—Bolted and Bonded,” the joints are the critical areas. They should be designed first and then the space between them should be filled in with appropriate laminates. Since most composite structures have some type of mechanically attached joints, the use of quasi-isotropic or near-quasi-isotropic...