1-20 of 488 Search Results for

adhesive

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 30 November 2013
DOI: 10.31399/asm.tb.uhcf3.t53630169
EISBN: 978-1-62708-270-9
... Abstract This chapter is a detailed account of the general characteristics and effects of and the methods for preventing or reducing different categories of wear failures, namely abrasive (erosive, grinding, and gouging), adhesive, and fretting wear. abrasive wear adhesive wear fretting...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.bcp.t52230441
EISBN: 978-1-62708-298-3
... Abstract This chapter explains how to join beryllium parts using adhesive bonding and mechanical fastening techniques and discusses the advantages and disadvantages of each method. It describes the stresses that need to be considered when designing adhesive bonds, the benefits and limitations...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290243
EISBN: 978-1-62708-306-5
... Abstract Adhesive bonding is a widely used industrial joining process in which a polymeric material is used to join two separate pieces (the adherends or substrates). This chapter begins with a discussion on the advantages and disadvantages of adhesive bonding, followed by a section providing...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.caaa.t67870161
EISBN: 978-1-62708-299-0
... Abstract This chapter describes the factors that affect the corrosion performance of aluminum assemblies joined by methods such as welding, brazing, soldering, and adhesive bonding. The factors covered include galvanic effects, crevices, and assembly stresses in products susceptible to stress...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870235
EISBN: 978-1-62708-314-0
... Abstract This chapter explains how polymeric adhesives are applied to composite as well as metal parts, forming bonded structures. It describes surface preparation practices and techniques, epoxy selection and use, and bonding procedures. adhesive bonding epoxy adhesives surface...
Image
Published: 01 November 2011
Fig. 1.2 Typical adhesive-bonded joint configurations. Note that the adhesive is loaded in shear in all configurations. Source: Ref 1.2 More
Image
Published: 01 July 2009
Fig. 24.4 Effect of aging conditions on an epoxy-film adhesive. A, fresh adhesive; B, cured after 90 days at 24 °C (75 °F); C, cured after 90 days at 32 °C (90 °F); D, cured after 1 h at 50 °C (122 °F) in a 95 to 100% humidity chamber. (Normal 120 °C, or 248 °F, cure cycle used after aging More
Image
Published: 30 June 2023
Fig. 10.21 Typical automotive joint combining adhesive bond with self-piercing rivets More
Image
Published: 30 June 2023
Fig. 10.23 Possible shear failure modes for adhesive joints. (a) Adhesion, (b) cohesion, and (c) mixed failures More
Image
Published: 01 August 2018
Fig. 11.53 (a) Replica, produced with transparent adhesive tape of the magnetic particle (MT) examination of the weld edges of a plate of structural steel WStE355. The plate is 38 mm (1.5 in.) thick. The indications are elongated in the direction of rolling. (b) Micrograph of the region More
Image
Published: 30 November 2013
Fig. 10 Scanning electron microscope image of a microscopic region of adhesive wear on a hardened-alloy-steel piston component from a hydrostatic pump (500×). Material has been transferred by microwelding from the adjacent component wall surface during sliding and poor lubrication conditions. More
Image
Published: 30 November 2013
Fig. 11 Severe adhesive wear on a stationary shaft upon which a planetary gear rotated in the presence of inadequate lubricant. Because the radial force was on only one side of the shaft, the adhesive wear was on only one side. However, the entire bore of the gear was damaged by adhesive wear More
Image
Published: 30 November 2013
Fig. 12 Destructive adhesive wear of a differential cross following fracture of one severely worn trunnion. This vehicle was operated primarily in forward speeds; consequently, only the forward-drive side was damaged severely by the rotation of differential pinions on the trunnions More
Image
Published: 01 October 2011
Fig. 16.6 Bronze transfer to a steel surface after adhesive wear during sliding contact. Source: Ref 16.3 More
Image
Published: 01 December 2009
Fig. 12.7 Cohesive failure. In this specimen, the adhesive adhered to both sides of the bonded material; it failed in the adhesive layer. More
Image
Published: 01 December 2003
Fig. 24 Multilayer construction of RC-205 adhesive material More
Image
Published: 01 November 2011
Fig. 1.8 Examples of (a) adhesive bond joint configurations and (b) honeycomb bonded assembly. Source: Ref 1.4 More
Image
Published: 01 November 2011
Fig. 9.2 Effect of different aluminum surface treatments on epoxy adhesive bond durability. Source: Ref 9.2 More
Image
Published: 01 November 2011
Fig. 9.3 Aluminum adhesive bonded system. Source: Ref 9.2 More
Image
Published: 01 November 2011
Fig. 9.4 Typical adhesively bonded joint configurations. The adhesive is loaded in shear in all configurations. Source: Ref 9.1 More