1-20 of 430 Search Results for

Wear tests

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2003
DOI: 10.31399/asm.tb.cfap.t69780259
EISBN: 978-1-62708-281-5
...Abstract Abstract This article focuses on friction and wear as they relate to polymeric materials, covering friction and wear applications for polymeric materials. The discussion covers the causes and mechanisms of friction, wear, and lubrication; different test methods developed to simulate...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350043
EISBN: 978-1-62708-315-7
...,” General Magnaplate Corporation, 1988 TMI Model 98-5 slip and friction tester, 1.96 N (0.200 kgf) load, ground specimens, 54% relative humidity, average of five tests 3. J.F. Archard, ASME Wear Control Handbook , M.B. Peterson and W.O. Winer, Ed., American Society of Mechanical Engineers, 1980, p 38...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300121
EISBN: 978-1-62708-323-2
... Fig. 5.17 Types of erosion tests Fig. 5.18 Common erosion tests Fig. 5.20 Test specimen configurations for wear testing Fig. 5.21 Stages of adhesive wear Fig. 5.22 Type 440C stainless steel shaft (57 HRC) versus a zirconia (PSZ) roller produced oxidative...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2012
DOI: 10.31399/asm.tb.smfpa.t53500317
EISBN: 978-1-62708-317-1
... hardening, case (surface) hardening, and nitriding as well as hard chrome plating, vapor deposition, and thermal diffusion coating. It explains how to measure wear resistance using various tests and provides guidelines for selecting tool materials, treatments, and coatings. chemical vapor deposition...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1984
DOI: 10.31399/asm.tb.mpp.t67850334
EISBN: 978-1-62708-260-0
..., machinability, wear, fracture toughness, and tensile strength as well as temperature effects, residual stress, and quality control. hardness hardness testing 5-1 Introduction O’Neill in his classic book on hardness states that “the hardness of metals, like the storminess of seas, is easily...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1999
DOI: 10.31399/asm.tb.cmp.t66770171
EISBN: 978-1-62708-337-9
... of slide/roll wear tests on 12KhN3A steel Table 7.20 Results of slide/roll wear tests on 12KhN3A steel Loading cycles Hardness, HV Carbon in martensite, % Wear, mg Small roller Large roller Carburized at 1000 °C to a depth of 1.8 mm; oil quenched from 900 °C and 800 °C 0 (before...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300271
EISBN: 978-1-62708-323-2
... in block-on-ring testing, where * indicates thermal spray coatings Fig. 10.23 Adhesive wear test results of cemented carbide (WC/6%Co) couples tested in a block-on-ring test rig (in accordance with ASTM International G77), where * indicates maximum working hardness Fig. 10.24 Wear...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300079
EISBN: 978-1-62708-323-2
... in a jacketed vessel Fig. 4.1 Types of erosion Fig. 4.15 Types of wear as defined by the ASTM G2 Committee on Wear and Erosion Fig. 4.16 An estimate of the relative frequency of occurrence of various types of wear Fig. 4.32 Schematic of tribocorrosion testing...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.9781627083232
EISBN: 978-1-62708-323-2
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300301
EISBN: 978-1-62708-323-2
... (polyethylene terephthalate) film. Original magnification: 32× Fig. 11.13 Wear results of block-on-ring tests on various plastics versus titanium and 316 stainless steel rings. POM, polyoxymethylene; PTFE, polytetrafluoroethylene; PE, polyethylene; PPS, polyphenylene sulfide; CF, carbon fiber; PI...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 February 2005
DOI: 10.31399/asm.tb.chffa.t51040295
EISBN: 978-1-62708-300-3
... ]. Upset forging conditions used in die wear tests [<xref ref-type="bibr" rid="t51040295-ref5">Bobke, 1991</xref>, and <xref ref-type="bibr" rid="t51040295-ref18">Luig, 1993</xref>] Table 22.3 Upset forging conditions used in die wear tests [ Bobke, 1991 , and Luig, 1993 ] Press Type...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300335
EISBN: 978-1-62708-323-2
..., thermal spray Fig. 12.8 Kinetic coefficient of friction of test couples measured during steady-state wear in the ASTM International G77 block-on-ring test Fig. 12.7 Three-body abrasive wear of surface treatments tested with the ASTM International G65 dry sand/rubber wheel abrasion test...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300179
EISBN: 978-1-62708-323-2
... recordings for 52100 steel at 60 HRC versus gray cast iron in reciprocating sliding in two different oils. The area of the force recordings are measures of the energy expended on friction during each test. Fig. 7.7 System wear results in reciprocating wear tests (ASTM G 133) of hard steel versus...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2000
DOI: 10.31399/asm.tb.aet.t68260213
EISBN: 978-1-62708-336-2
... billet-making and extrusion processes, die construction, equipment maintenance, heat treating, and sawing and stretching procedures. It also discusses the importance of charting test results and monitoring surface treatments that may be required to improve corrosion, oxidation, or wear resistance...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300047
EISBN: 978-1-62708-323-2
... , Oxford University Press , New York , 1950 4. Kragel’skii I.V. and Myshkin N.M. , Handbook of Frction Units of Machines , ASME Press , New York , 1988 . p 31 Selected References Selected References • Bayer R. , Mechanical Wear Fundamentals and Testing...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300227
EISBN: 978-1-62708-323-2
... in the ASTM G65 test procedure Fig. 9.20 Wear of Ti6Al4V pins versus various counterfaces in a pin-on-disk wear test Fig. 9.21 Effect of counterface hardness on the fretting wear of titanium 6Al4V versus various stainless steels in a pin-on-flat test (after ASTM G204) Fig. 9.11...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300363
EISBN: 978-1-62708-323-2
... up into the heart to do an angiogram. Needless to say, this medical device must have low friction and produce low wear in its total sliding distance. Friction testing of probe materials against the inside of arteries is used to optimize the materials and coating on these components. In fact...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.tb.hpcspa.t54460209
EISBN: 978-1-62708-285-3
... substrate ( Fig. 8.13 ). Fig. 8.13 Cross-sectional images of (a) as-sprayed and (b) heat treated 316L stainless steel coating layers. Results of their (c) tensile strength measurement and (d) wear test. Source: Ref 8.51 Gojon et al. studied the effect of ball-milled SiC particle size...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 June 2016
DOI: 10.31399/asm.tb.hpcspa.t54460185
EISBN: 978-1-62708-285-3
... not penetrate the coating, and the coupons did not show pitting after 500 h of electrochemical testing in 3.5% NaCl solution. Wear-protection coatings are usually formed by spraying ceramics or cermets. Cermets use hard particles in a metallic matrix. Cermets contain metallic phases of cobalt, chromium...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2021
DOI: 10.31399/asm.tb.tpsfwea.t59300391
EISBN: 978-1-62708-323-2
... Four-ball wear scar diameter, mm (ASTM International D2266) 0.4 Dropping point, °C (°F) 271 (520) Weld point in four-ball extreme-pressure test, kgf (ASTM International D2596) 295 Load in Timken OK extreme-pressure test, lbf (ASTM International D2509) 41 Oxidation stability, kPa (psi...