The qualities that make superalloys excellent engineering materials also make them difficult to machine. This chapter discusses the challenges involved in machining superalloys and the factors that determine machinability. It addresses material removal rates, cutting tool materials, tool life, and practical issues such as set up time, tool changes, and production scheduling. It describes several machining processes, including turning, boring, planing, trepanning, shaping, broaching, drilling, tapping, thread milling, and grinding. It also provides information on toolholders, fixturing, cutting and grinding fluids, and tooling modifications.

Beryllium’s machining characteristics are similar to those of heat-treated cast aluminum and chilled cast iron. Like the other materials, it can be turned, milled, drilled, bored, sawed, cut, threaded, tapped, and trepanned with good results. This chapter explains how these machining operations are conducted and describes the effect of tooling materials, cutting speeds, metal-removal rates, and other variables. It also explains how to assess and remove surface damage caused by machining such as microcracks and twins.

This chapter presents a comprehensive coverage of mechanical fastening methods. It begins with a discussion on the advantages and disadvantages of mechanical fastening followed by sections providing information on mechanically fastened joints and the selection of the correct fastener system. The chapter then describes important structural fasteners, namely bolts, screws, pins, collar fasteners, rivets, blind fasteners, machine pins, and spring clip fasteners. The following sections describe the process involved in presses, shrink fits, hole generation, and fastener installation. The chapter ends with information on miscellaneous mechanical fastening methods.

Stop-off coatings prevent nitriding of selected areas on components. This chapter discusses the processes, advantages, and disadvantages of stop-off techniques for gas nitriding, salt bath nitriding, and ion nitriding.

This appendix provides an extensive amount of data corresponding to titanium machining processes, including sawing, turning, drilling, reaming, tapping, broaching, face milling, end milling, slotting, surface grinding, and thermal cutting.

This chapter covers the practical aspects of machining, particularly for turning, milling, drilling, and grinding operations. It begins with a discussion on machinability and its impact on quality and cost. It then describes the dimensional and surface finish tolerances that can be achieved through conventional machining methods, the mechanics of chip formation, the factors that affect tool wear, the selection and use of cutting fluids, and the determination of machining parameters based on force and power requirements. It also includes information on nontraditional machining processes such as electrical discharge, abrasive jet, and hydrodynamic machining, laser and electron beam machining, ultrasonic impact grinding, and electrical discharge wire cutting.

This chapter discusses the various methods used to join titanium alloy assemblies, focusing on welding processes and procedures. It explains how welding alters the structure and properties of titanium and how it is influenced by composition, surface qualities, and other factors. It describes several welding processes, including arc welding, resistance welding, and friction stir welding, and addresses related issues such as welding defects, quality control, and stress relieving. The chapter also covers mechanical fastening techniques along with adhesive bonding and brazing.

Unlike conventional quench and temper heat treatment, austempering is an iron and steel heat-treatment process that enhances mechanical properties through the isothermal transformation of austenite with a minimum amount of quenching stresses. This chapter begins with a discussion of austemperability requirements. Then outlines of austenitizing and austempering cycles and resultant microstructures are presented. This is followed by sections discussing the mechanical properties, advantages, limitations, machinability, process variants, and applications of austempered ductile iron (ADI). Information on the growth of premachined ADI components is also provided. Further, the chapter describes two slightly different systems for austempering: atmospheric-salt and salt-salt systems. Finally, it presents general guidelines for component designers, casting manufacturers, and heat treaters to apply ADI more widely and with improved success.

This chapter provides a discussion of nitriding furnace equipment and control systems. The discussion covers the essential design criteria of the furnace, types of nitriding furnaces, insulation for the reduction of furnace heat losses, and factors influencing furnace configuration and design. It also covers the processes involved in the construction and maintenance of retorts, methods for sealing a retort to prevent ammonia leaks, and safety precautions to be taken while using ammonia. Further, the chapter provides information on the factors for choosing a heating medium and discusses the processes involved in controlling temperature, gas dissociation, oxygen probes, and nitriding sensors.

This chapter introduces the key powder fabrication attributes to assist in the identification of the right powders for an application. First, it describes the characteristics of engineering powders such as particle size distribution, powder shape and packing density, surface area, powder flow and rheology, and chemical analysis. The chapter then describes the general categories of powder fabrication methods, namely mechanical comminution, electrochemical precipitation, thermochemical reaction, and phase change and atomization. It provides information on the two largest contributors to powder price, namely raw material cost and conversion cost. The applicability of various processes to specific material systems is mentioned throughout this chapter.

This chapter explains how to join beryllium parts using adhesive bonding and mechanical fastening techniques and discusses the advantages and disadvantages of each method. It describes the stresses that need to be considered when designing adhesive bonds, the benefits and limitations of different adhesives, and surface preparation requirements. It explains how adhesives are applied and cured and how curing times and temperatures affect bonding strength. It also discusses the use of bolts and rivets and the different types of joints that can be made with them.

This chapter familiarizes readers with the machining characteristics of titanium and the implementation of machining and shaping processes. It explains why titanium alloys are more difficult to machine than other metals and how it impacts the equipment and procedures that can be used. It describes the basic machining requirements for titanium in terms of tool geometry and materials, machine setup rigidity, cutting speeds and feed rates, and surface conditions, and explains how the requirements are met in practice in milling, turning, drilling, surface grinding, and broaching operations. The chapter also covers chemical and electrochemical machining processes as well as flame cutting.

Environmentally assisted cracking is a generic term that includes various cracking phenomena such as stress-corrosion cracking (SCC), corrosion fatigue cracking, and liquid-metal embrittlement. This chapter describes these cracking mechanisms beginning with SCC and the factors that influence its formation. It covers alloy selection and mitigation techniques and includes examples of SCC in aircraft components. The chapter also addresses corrosion fatigue, explaining how different environments and operating conditions affect crack propagation, fatigue strength, and fatigue life. It includes information on liquid-metal embrittlement as well.

Coil design for induction heating has been developed and refined over time based on the theoretical principles applied in practice to several simple inductor geometries such as the classical solenoidal coil. This chapter reviews the fundamental considerations in the design of inductors and describes some of the most widely used coils and common design modifications. Specialty coil designs for specific applications are also discussed. The chapter concludes with sections devoted to coil fabrication and design of power-supply leads.

This chapter discusses the maintenance needs of major components in induction heat-treating systems, including power supplies, heat stations, capacitors, high-frequency output stages, induction coils, water systems, quench systems, and fixturing.

This chapter is largely a compendium of best practices and procedures for minimizing the effects of fatigue. It explains how to make products more resistant to fatigue by choosing the right materials and manufacturing processes, avoiding geometries and features that concentrate strains, preventing or removing surface damage, and by inducing compressive mean stresses that prolong fatigue life. It also discusses the use of property conditioning and restoration treatments, the benefits of interference fits and processes such as coaxing, the effects of assembly damage and operating overload, the importance of surface cleanliness and finish, and the role of inspection, testing, replacement, and repair in safe-life and fail-safe designs. Examples highlighting the benefits and potential pitfalls of proof loading tests are included as well.

This chapter discusses the fusion welding processes, namely oxyfuel gas welding, oxyacetylene braze welding, stud welding (stud arc welding and capacitor discharge stud welding), high-frequency welding, electron beam welding, laser beam welding, hybrid laser arc welding, and thermit welding.

This chapter provides practical information on surface treatments that work by altering the surface chemistry of metals and alloys. It discusses the use of phosphate and chromate conversion coatings as well as anodizing, steam oxidation, diffusion coatings, and pack cementation. The chapter also covers ion implantation and laser alloying.

Joining comprises a large number of processes used to assemble individual parts into a larger, more complex component or assembly. The selection of an appropriate design to join parts is based on several considerations related to both the product and the joining process. Many product design departments now improve the ease with which products are assembled by using design for assembly (DFA) techniques, which seek to ensure ease of assembly by developing designs that are easy to assemble. This chapter discusses the general guidelines for DFA and concurrent engineering rules before examining the various joining processes, namely fusion welding, solid-state welding, brazing, soldering, mechanical fastening, and adhesive bonding. In addition, it provides information on several design considerations related to the joining process and selection of the appropriate process for joining.