1-20 of 509 Search Results for

Steel wire

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 2015
Fig. 19 Fretting fatigue failure of steel wire rope after seawater service. Wire diameter was 1.5 mm (0.06 in.). See also Fig. 20 . Courtesy of R.B. Waterhouse, University of Nottingham More
Image
Published: 01 August 2018
Fig. 12.36 Longitudinal cross section of a AISI 1006 steel wire with diameter of 1.15 mm (0.05 in.) (a) As drawn (cold worked). (b) Annealed. Etchant: nital 2%. Courtesy of ArcelorMittal Aços Longos, Juiz de Fora, MG, Brazil. More
Image
Published: 01 August 2018
Fig. 12.37 Longitudinal cross section of a AISI 1006 steel wire cold drawn from 5.5 to 1.15 mm (0.2 to 0.06 in.) diameter. (a) As drawn (cold worked), hardness 249 HV 100 gf. (b) Annealed, hardness 135 HV 100 gf. The hardness impressions, performed with the same load, are visible More
Image
Published: 01 August 2018
Fig. 13.16 Longitudinal cross section of a steel wire containing C = 0.06–0.15%, Si = 0.80–1.15%, Mn = 1.40–1.85% (AWS A5.18 ER 70S-6). Equiaxed ferrite (gray) and banded pearlite (dark). Islands of martensite-austenite (MA) appear white. Sample was austenitized at 900 °C (1650 °F), cooled More
Image
Published: 01 September 2008
Fig. 29 Optical micrograph of an oxide-lined seam in a piece of steel wire More
Image
Published: 01 March 2002
Fig. 7.32 Procedure to mount steel wire specimens. (a) Wires are placed in drilled holes in the mount. (b) A masking tape dam is provided to hold the castable epoxy around the specimens. 1.2× More
Image
Published: 01 March 2002
Fig. 4.8 Microstructure taken at the center of a fractured AISI/SAE 1070 steel wire. Fracture is associated with a central bursting condition. Unetched. 50× More
Image
Published: 01 March 2002
Fig. 4.9 Micrograph taken at the fracture of an AISI/SAE 1070 steel wire showing hard regions of martensite that caused the rupture of the wire. Picral etch. (a) at 100× and (b) at 200× More
Image
Published: 01 December 2006
Fig. 34 Pitting corrosion associated with stainless steel wire brush cleaning on the back of a type 316L stainless steel test coupon after bleach plant exposure. Source: Ref 4 More
Image
Published: 01 July 1997
Fig. 5 Upset butt welded steel wire showing typical acceptable burrs on the welds. Dimensions given in inches More
Image
Published: 01 December 2015
Fig. 18 Pitting corrosion associated with stainless steel wire brush cleaning on the back of a type 316L stainless steel test coupon after bleach plant exposure. Source: Ref 5 More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 April 2013
DOI: 10.31399/asm.tb.imub.t53720321
EISBN: 978-1-62708-305-8
... Abstract This chapter focuses on the inspection of steel bars for the detection and evaluation of flaws. The principles involved also apply, for the most part, to the inspection of steel wire. The nondestructive inspection methods discussed include magnetic particle inspection, liquid penetrant...
Image
Published: 01 January 2017
Fig. 4.6 Effect of nickel content on SCC susceptibility of stainless steel wires containing 18 to 20% Cr in a magnesium chloride solution boiling at 154 °C (309 °F). After Ref 4.23 More
Image
Published: 01 August 2018
Fig. 6.10 Atom probe tomography results of pearlitic steel wires cold drawn to different strains (indicated in the pictures). 3D carbon atom maps parallel and transverse to the wire drawing direction are shown. Dots are carbon atoms. Carbon iso-concentration surfaces 7 at.% are shown. Figure More
Image
Published: 01 December 2015
Fig. 14 Carbon steel wires from a prestressing tendon of a nuclear power plant showing the damage resulting from the formation of organic acids in the tendon due to the breakdown of grease by the bacteria present in the tendon. Source: Ref 9 More
Image
Published: 01 August 2018
Fig. 14.17 Transverse cross section of wire rod of AISI 1045 steel annealed (a) and (c) and subjected to forced air accelerated cooling (Stelmor) from the austenitic region (b) and (d). Lever-rule calculations are applicable only to cooling near equilibrium, which is the case of the annealed More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.spsp2.t54410315
EISBN: 978-1-62708-265-5
... Abstract This chapter describes the mechanical properties of fully pearlitic microstructures and their suitability for wire and rail applications. It begins by describing the ever-increasing demands placed on rail steels and the manufacturing methods that have been developed in response...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2005
DOI: 10.31399/asm.tb.faesmch.t51270158
EISBN: 978-1-62708-301-0
... Abstract This chapter discusses the failure of a control cable on an aircraft and the findings of an investigation that followed. The cable was made of stranded steel wire that was visibly worn. All seven strands had snapped and bore evidence of corrosion, pitting, nicks, and rubbing. Based...
Image
Published: 01 December 2003
nesting together. Basket may be made of carbon or alloy steel rod and steel wire mesh. Work must be free from oil, or the parts will stick together. Parts must be dry. (b) Inconel basket of simple design. Upper loop of the handle is for lifting; lower loop accommodates a rod which supports the basket over More
Image
Published: 01 January 2015
Fig. 15.8 Tensile strength as a function of wire diameter for patented and drawn pearlitic hypereutectoid steel wires. Source: Ref 15.29 More