1-18 of 18 Search Results for

Scouring

Sort by
Image
Published: 01 March 2001
Fig. 15 Slurry erosion wear modes. (a) Abrasion-corrosion. (b) Scouring wear, with wear areas equal (left) and unequal (center and right). (c) Crushing and grinding. (d) High-velocity erosion. (e) Low-velocity erosion. (f) Saltation erosion. (g) Cavitation More
Series: ASM Technical Books
Publisher: ASM International
Published: 30 November 2013
DOI: 10.31399/asm.tb.uhcf3.t53630169
EISBN: 978-1-62708-270-9
... of soft surface coatings or material: This is a common form of wear for fan and propeller blades. In automotive applications, for example, the paint on the rear, or concave, side of the blade is usually removed by the scouring or cutting action of dust and dirt particles in the air. The concave side...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 September 2023
DOI: 10.31399/asm.tb.stmflw.t59390001
EISBN: 978-1-62708-459-8
... conceivable household needs, and it is reasonable to assume that this was used for drawing the highest grades of iron and, later, steel wires. It was in Altena that the first surface treatment was discovered. For many centuries the wire had been prepared for drawing by hand scouring it with bricks or sand...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.t52310193
EISBN: 978-1-62708-286-0
.... Oxides, heat tint If severe, treat by pickling; Scotchbrite © , stainless scouring pad, or nonscratching cream or polish If abrasives must be used, they should blend with existing surface finish in size and direction. Paint Alkaline, trisodium phosphate, or hydrocarbon solvent Follow...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870101
EISBN: 978-1-62708-314-0
..., it is necessary to place a metal shim between the ply and the tool to prevent scouring of the tool surface. In general, this is a bad practice since it increases the chance of the shim being left in the lay-up through cure, producing a possible repair or scrap condition. An additional consideration...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2012
DOI: 10.31399/asm.tb.ffub.t53610461
EISBN: 978-1-62708-303-4
..., side of the blade is usually removed by the scouring or cutting action of dust and dirt particles in the air. The concave side of a rotating fan blade has a positive pressure, while the convex side has negative pressure, and the positive pressure forces the particles against the surface, thus leading...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2022
DOI: 10.31399/asm.tb.isceg.t59320103
EISBN: 978-1-62708-332-4
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2015
DOI: 10.31399/asm.tb.cpi2.t55030117
EISBN: 978-1-62708-282-2
... of erodent particles is so great that the independent action of individual particles is unlikely, the form of damage may be more similar to scouring from particles embedded in a massive backing than that from discrete particle impacts. Rules derived for abrasive wear may then be more appropriate. In a large...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350043
EISBN: 978-1-62708-315-7
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.9781627083157
EISBN: 978-1-62708-315-7
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350231
EISBN: 978-1-62708-315-7
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870031
EISBN: 978-1-62708-314-0
... for only about one to two percent by weight. The sizing (usually a starch and a lubricant) can be removed by either solvents or heat scouring after all mechanical operations are completed. After the sizing is removed, it is replaced with a surface finish that greatly improves the fiber-to-matrix bond...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.caaa.t67870191
EISBN: 978-1-62708-299-0
... lines ( Fig. 13a ). The black marks were coherent with the metal and could not be removed by scouring or light sanding. The panels, subsequent to profiling and machining, were required to be penetrant inspected, shot peened, sulfuric acid anodized, and coated with MIL-C-27725 integral fuel tank coating...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 1999
DOI: 10.31399/asm.tb.lmcs.t66560309
EISBN: 978-1-62708-291-4
... mechanics. The accelerated plate in fact divides at the interface into two jets, called the salient and re-entrant jets ( Fig. 11.10e ), and the re-entrant jet sweeps the interface and scours off the contaminated surface layers. The two clean surfaces so produced are then pressed together by the explosive...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2010
DOI: 10.31399/asm.tb.scm.t52870119
EISBN: 978-1-62708-314-0
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910099
EISBN: 978-1-62708-250-1
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2015
DOI: 10.31399/asm.tb.cpi2.t55030247
EISBN: 978-1-62708-282-2
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.9781627082860
EISBN: 978-1-62708-286-0