1-20 of 843 Search Results for

Rotation

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 30 September 2023
Figure 9.31: Change in frictional stresses during die rotation. More
Image
Published: 01 November 2019
Figure 22 SEM image at 30 degrees tilt and 45 degrees rotation. More
Image
Published: 01 August 2005
Fig. 5 The offsetting effect of rotation on fatigue fracture beach marks reveals the direction of shaft rotation during operations More
Image
Published: 01 June 2008
Fig. 16.27 Grain-boundary rotation. Source: Ref 13 More
Image
Published: 01 October 2005
Fig. 2.4 Diagram showing the directions of rotation of the turbine disk and the locking nut. Source: Ref 3 More
Image
Published: 01 September 2011
Fig. 2.16 Continuous curing oven with part rotation More
Image
Published: 01 June 1988
Fig. 10.20 Robot design including three arms, 90° wrists, and gripper rotation. From M. R. Farber and G. P. Welch, Industrial Heating , Vol 53, No. 7, July, 1986, p 24 ( Ref 10 ) More
Image
Published: 01 November 2010
Fig. 4.10 Schematic showing the complementary rotation of the head and platen (polishing surface). The head is shown to travel partially off of the polishing surface to facilitate cleaning. More
Image
Published: 01 December 2006
Fig. 4.37 Rotation of single crystal during deformation More
Image
Published: 01 August 2005
Fig. 8.8 Stress coordinate rotation More
Image
Published: 01 August 2005
Fig. 8.9 Off-axis stiffness constants as functions of rotation angle θ. Source: Ref 8.3 More
Image
Published: 01 December 1995
Fig. 2-3 In a rotary dumping station, a coal car begins 180 degree rotation around the rugged cast steel rotary coupler. More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.aacppa.t51140253
EISBN: 978-1-62708-335-5
... Abstract This data set contains the results of rotating-beam reversed-bending fatigue tests for a wide range of aluminum casting alloys. These fatigue curves are the results of tests on individual lots of material considered representative of the respective alloys and tempers. aluminum...
Image
Published: 30 June 2023
Fig. 5.15 Rotating beam fatigue plot of gravity-cast automotive diesel engine block (AlSi7MgCu0.5). The solid lines through the data represent a second-order regression. The dashed lines represent 95% confidence limits. Source: Ref 5.22 More
Image
Published: 30 June 2023
Fig. 9.14 Comparison of rotating-beam (reversed bending, R = –1) fatigue data for two aluminum alloys in various product forms: (a) 2024-T4 and (b) 7075-T6. Source: Ref 9.10 More
Image
Published: 01 June 1985
Fig. 4-33. A 4-in.-diameter keyed shaft. Reversed bending; rotational load; high stress concentration; high over-stress. More
Image
Published: 01 June 1985
Fig. 4-34. A 5-in.-diameter taper splined shaft. Reversed bending; rotational load; very high stress concentration; high overstress. More
Image
Published: 30 September 2023
Figure 10.14: The friction stir extrusion process, illustrating a rotating die pressed into a container filled with powder or machining chips/swarf. Frictional heating and pressure consolidate the powder and push the material through a die as shown. More
Image
Published: 01 September 2008
Fig. 24 Heating profile on rotational workpiece with induction coil. Source: Ref 42 More
Image
Published: 01 September 2008
Fig. 25 Heating profile on rotational workpiece with flux concentrator. Source: Ref 42 More