1-20 of 53 Search Results for

Microwaves

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 November 2019
Figure 4 Overview of the microwave decapsulation system. The faraday cage is the key to lowering the process temperature and preventing heat absorption and metallization sputtering. [5] More
Image
Published: 01 November 2019
Figure 5 Decapsulation of laser-ablated PBGA microcircuit using downstream microwave plasma. This takes about two hours on an older 300-watt system, and less than 20 minutes on the newer 500-watt systems. [6] More
Image
Published: 01 August 2005
Fig. 3.14 An electron gun of a klystron (high-power microwave amplifier) operating in the S-band (2.60–3.95 GHz). Courtesy of TMD Ltd. More
Image
Published: 01 October 2012
Fig. 9.3 A SiC/Al radio frequency microwave package used in commercial low-Earth orbit communications satellites. Courtesy of General Electric Company. Source: Ref 9.3 More
Image
Published: 01 April 2004
Fig. 3.27 Fluxless soldering of a GaAs monolithic microwave integrated circuit, approximately 3 × 5 mm (0.12 × 0.12 in.) achieved by application of a compressive load of 100 g/mm 2 (140 psi) during the heating cycle. Source: BAE Systems More
Image
Published: 01 October 2012
Fig. 1.23 Cast discontinuous aluminum-matrix composites. (a) An Al-SiC p composite brake rotor. (b) Aluminum-SiC microwave radio-frequency packaging for communication satellites. Source: Ref 1.10 More
Image
Published: 01 November 2019
Figure 6 Corner copper bond wires which fall off during acid decapsulation likely contain slip plane fractures like those seen here on a unit that was decapsulated using Microwave plasma. [7] More
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110485
EISBN: 978-1-62708-247-1
... Capacitance Microscopy, Scanning Spreading Resistance Microscopy, Conductive-AFM, Magnetic Force Microscopy, Scanning Surface Photo Voltage Microscopy, and Scanning Microwave Impedance Microscopy. An overview of each SPM technique is given along with examples of how each is used in the development of novel...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110144
EISBN: 978-1-62708-247-1
... plate contains the part to be etched. The resulting plasma is anisotropic using O2 or some form of Fluorine mixed with O2 to accelerate the etch. Figure 4 is an overview of a microwave based plasma system with advantages of lower processing temperatures and reduced sputtering effects over a standard...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2020
DOI: 10.31399/asm.tb.bpapp.t59290201
EISBN: 978-1-62708-319-5
... or 2490 °F). Other than microwave sintering, almost any furnace is successful in sintering 17–4 PH. Most common is vacuum or hydrogen sintering. Continuous pusher-plate or walking beam hydrogen furnaces are used to sinter millions of cell telephone parts every day, while batch vacuum or hydrogen...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2011
DOI: 10.31399/asm.tb.jub.t53290165
EISBN: 978-1-62708-306-5
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110545
EISBN: 978-1-62708-247-1
... for microwave reflection decay measurements [10-13]. Emission imaging of photovoltaics covers the full spectrum from the infrared to visible range with each range providing different information. In the infrared, thermal emission can be used to image local heating as discussed above. In the near infrared...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2009
DOI: 10.31399/asm.tb.sfa.t52780025
EISBN: 978-1-62708-268-6
... to start. Then, the ideas start to flow freely (so much so that keeping up with documenting the ideas can be difficult). After a while, the process decelerates, and ideas flow much less freely. The idea-generation process seems to follow the same pattern as making microwave popcorn. At first, not much...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2019
DOI: 10.31399/asm.tb.mfadr7.t91110016
EISBN: 978-1-62708-247-1
... [7] ISTFA 2017 Technical Program, “ Case Study of a DDR Loopback Test Failure Encountered on a Map Ball Grid Array Packaged Device ”, by Garcia Jose Z. III and Dickson Kris [8] ECTC 2015 Technical Program, “ Failure analysis of complex 3D stacked-die IC packages using Microwave...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550511
EISBN: 978-1-62708-307-2
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2023
DOI: 10.31399/asm.tb.edfatr.t56090021
EISBN: 978-1-62708-462-8
... of interest for milling ( Fig. 30 , 31 ) ( Ref 20 , 21 ). Fig. 30 A 7 nm product from Xilinx that was locally thinned to 50 μm RST ( Ref 20 ) Fig. 31 Module after MIP decapsulation ( Ref 22 ) In some cases, it may even be possible to perform chemical or microwave-induced plasma (MIP...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.t52310233
EISBN: 978-1-62708-286-0
... are increasingly using stainless. These include refrigerators, stoves, microwaves, drawers, etc. Shelves and exhaust hoods also benefit from being made of stainless. The drivers here are cleanability, durability, and esthetics. There are important visual considerations in these applications. Consistent, defect...
Series: ASM Technical Books
Publisher: ASM International
Published: 30 April 2020
DOI: 10.31399/asm.tb.bpapp.t59290251
EISBN: 978-1-62708-319-5
... and Microwave Exposure: From Non-Conductive Ink to 40% Bulk Silver Conductivity in Less Than 15 Seconds , Adv. Mater. , Vol 24 , 2012 , p 2620 – 2625 10.1002/adma.201104417 • Samanta S.K. , Das P. , Lohar A.K. , Kumar S. , Chattopadhyay D.P. , and Chowdhury A.K...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2012
DOI: 10.31399/asm.tb.lmub.t53550325
EISBN: 978-1-62708-307-2
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.pb.t51230105
EISBN: 978-1-62708-351-5