1-20 of 174 Search Results for

Liners

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Image
Published: 01 December 1995
Fig. 2-46 First compartment shell liners in a ball mill. These liners have a through hardness of 52 Rockwell C. More
Image
Published: 01 December 1995
Fig. 2-47 Shell liners and discharge grates in a ball mill used for cement production More
Image
Published: 01 September 2011
Fig. 2.10 Rotational molders to create the liners More
Image
Published: 01 December 2004
Fig. 3.21 Metal-matrix composite (MMC) cylinder liners. The MMC offers an alternative to cast iron or hypereutectic aluminum-silicon alloy for this application. More
Image
Published: 01 January 2022
Fig. 12.115 Dredger pump with manganese steel side liners. Source: Ref 4 More
Image
Published: 01 December 1995
Fig. 19-18 Relationship between weight losses of liners in laboratory and service conditions ( 21 ) More
Image
Published: 01 November 2019
Figure 70 SEM image of a FIB-cross section through the TSV. The oxide liner between the filling and the Si shows a delamination where pointed to by arrows. More
Image
Published: 01 November 2019
Figure 34 Higher magnification STEM-in-SEM image resolving a titanium plug liner and barrier layer. More
Image
Published: 01 August 2012
Fig. 12.31 (a) Gas bottle neck, formed by hot flow forming. (b) Gas liner. Source: Ref 12.15 More
Image
Published: 01 July 2009
Fig. 10.20 Typical louvered-constructed combustor liner showing airflow distribution More
Image
Published: 01 December 2006
Fig. 7.98 (a) Combination heating and cooling system. Source: Groos. (b) Liner holder with cooling grooves. Source: Böhler More
Image
Published: 01 December 2006
Fig. 7.100 Temperature at the internal liner bore and the mantle internal diameter measured on a container with cooling (broken line) and without cooling (solid line). Source: Groos More
Image
Published: 01 December 2006
Fig. 7.122 Solder fracture in the liner of the container of an aluminum extrusion press with a 250 mm bore after a large number of extrusions with the bearing material AlSn6Cu1. The liner was manufactured in the hot working steel 1.2306. Source: VAW More
Image
Published: 01 June 1988
Fig. 8.11 Method of inserting a liner in a coil to widen the flux path More
Image
Published: 01 June 1988
Fig. 8.47 Use of a liner on a single-turn channel coil to provide a wider heating pattern on the workpiece. From F. W. Curtis, High Frequency Induction Heating , McGraw-Hill, New York, 1950 ( Ref 1 ) More
Image
Published: 01 June 1988
Fig. 8.49 Multiturn channel coil with a liner added to control the heating pattern. From F. W. Curtis, High Frequency Induction Heating , McGraw-Hill, New York, 1950 ( Ref 1 ) More
Image
Published: 01 June 1988
Fig. 8.65 Photograph of a radio-frequency two-turn coil with a liner, showing fishtail-lead construction Source: Lindberg Cycle-Dyne, Inc. More
Image
Published: 01 January 2022
Fig. 12.114 Jaw liner plates of a jaw crusher More
Image
Published: 01 March 2000
Fig. 10 Round container with liner. Source: Edelstahlwerke Buderus AG More
Image
Published: 01 October 2012
Fig. 9.2 Cutaway section of the Honda Prelude 2000 cm 3 cast aluminum engine block with integral metal-matrix composite (MMC) piston liners. A cross section of the MMC liners is shown in the inset. These piston liners have been in production since 1990. Source: Ref 9.2 More