1-9 of 9 Search Results for

18Cr-8Ni-3Mo

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 July 2009
DOI: 10.31399/asm.tb.fdmht.t52060021
EISBN: 978-1-62708-343-0
... 31A 1Cr-1Mo-0.25V (casting) ASTM A356-9 1984 32 18Cr-8Ni (base metal, weld metals, and welded joints) JIS SUS 304-HP 1982 33 Fe-base 21Cr-20Ni-20Co-3Mo-2.5W-(Nb+Ta)-N (casting and forging) … 1984 34A Ni-base 19C4-18Co-4Mo-3Ti-3Al-B (casting and forging) … 1989 35A 1Cr-0.5Mo...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.htcma.t52080067
EISBN: 978-1-62708-304-1
... of these nitrides can be found in Ref 9 . The types of nitrides that are likely to form in the alloy can be predicted by examining the phase-stability diagram. Figure 4.3 shows a phase-stability diagram of Fe-18Cr-Ni-N system at 900 °C (1650 °F), indicating phase regions of Cr 2 N in γ (or α+γ) phase...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910331
EISBN: 978-1-62708-250-1
... concentrations. Pitting resistance is increased by adding molybdenum, and machinability is increased by adding sulfur. However, the addition of sulfur lowers corrosion resistance—an example of a trade-off in alloy design. To control sensitization of 18Cr-8Ni stainless steel, either the carbon content is reduced...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2015
DOI: 10.31399/asm.tb.spsp2.t54410579
EISBN: 978-1-62708-265-5
... stainless steels. Many heat-resisting grades of stainless steel have austenitic structures. The heat-resisting grades have much higher chromium and nickel contents for scaling resistance and high-temperature strength compared with the 18Cr-8Ni types of stainless steel. Again, there are counterpart...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.htcma.9781627083041
EISBN: 978-1-62708-304-1
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910099
EISBN: 978-1-62708-250-1
... jetty after 8 years. Although the washer shows severe deterioration, the function of the fastener was not diminished. On the other hand, Fig. 9 shows crevice corrosion beneath the water-box gasket of an alloy 825 (44Ni-22Cr-3Mo-2Cu) seawater heat exchanger that allowed sufficient leakage to warrant...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 November 2007
DOI: 10.31399/asm.tb.htcma.t52080005
EISBN: 978-1-62708-304-1
... of the furnace), Types 409 (12Cr), 420 (13Cr), and 304 (18Cr-8Ni) suffered severe attack. Type 420 (13Cr) was completely oxidized after only 100 cycles, although the sample did not show any weight changes. Alloys that performed well under these conditions were Types 405 (14Cr), 430 (17Cr), 446 (25Cr), 310 (25Cr...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2008
DOI: 10.31399/asm.tb.fahtsc.t51130001
EISBN: 978-1-62708-284-6
... expansion ( Table 2 ) in going from room temperature to 700 °C (1300 °F) is approximately: 10.3 mm/m (0.124 in./ft) for low-alloy steel 8.5 mm/m (0.102 in./ft) for martensitic stainless steel (type 13Cr) 13.1 mm/m (0.157 in./ft) for austenitic stainless steel (type 18Cr-8Ni). Linear thermal...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2000
DOI: 10.31399/asm.tb.cub.t66910237
EISBN: 978-1-62708-250-1
..., and alternating acid-alkali conditions. High-silicon cast irons are defined in ASTM standards A 518 and A 861. In addition, some proprietary compositions not included in these standards, such as alloy SD77 (Fe-4Cr-3Mo-16Si-1Mn-1C), are manufactured for high-temperature HCl service. Graphitic Corrosion...