1-14 of 14 Search Results for

(Other, general, or unspecified) processing-related failures

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2008
DOI: 10.31399/asm.tb.fahtsc.t51130087
EISBN: 978-1-62708-284-6
.... The term damage is often preferable to the term failure , because damage is a technical term that is very clear and has a specific meaning, generally related to the physical condition of the component. The term failure , on the other hand, has many more philosophical connotations. It is possible to see...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.t69870105
EISBN: 978-1-62708-344-7
... axial loading. Almost immediately it was recognized that for other materials this relation was not necessarily true; completely reversed torsion and completely reversed axial loading required the same octahedral shear plastic strain for such materials. Thus, a cloud was cast on the general validity...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090419
EISBN: 978-1-62708-266-2
... in a stress state of sufficient magnitude to induce fracture. Analysis of SCC service failures is quite involved and requires prescribed and thorough examination procedures. Appropriate methodologies for evaluating such service failures are the subject of this chapter. Other processes that cause failure...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350043
EISBN: 978-1-62708-315-7
... are forced to move relative to each other. It is closely associated with any wear mechanisms that may be operating and with any lubricant and/or surface films that may be present, as well as the surface topographies. The heat generated as a result of the dissipation of frictional interaction may affect...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.t60490329
EISBN: 978-1-62708-340-9
... are those of hydroprocessors. The term “hydroprocessing” represents a wide range of refining processes including hydrocracking, hydrodesulfurization, and others in which oil is reacted with hydrogen in the presence of a catalyst at high pressures (up to 27.6 MPa, or 4000 psi) and high temperatures (345...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.9781627083409
EISBN: 978-1-62708-340-9
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540001
EISBN: 978-1-62708-309-6
... material consists of six quantities. This means that both materials have the same form of equations. One group of the equations can be transformed into the other group if the quantities appearing in the stress-strain relations (ε x , ε y , ε z , γ yz , γ zx , γ xy , E , and G ) are replaced...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540169
EISBN: 978-1-62708-309-6
... testing of cracked plates has shown that, in general, fracture strengths are significantly below the net section yield limit (see Fig. 4.2 ). In other words, the remaining cross-sectional area of the cracked plate could not support the applied load as was assumed. Clearly, conventional stress analysis...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060429
EISBN: 978-1-62708-261-7
...). A generic term denoting a air-hardening steel. A steel containing suffi- treatment consisting of heating to and holding cient carbon and other alloying elements to harden fully during cooling in air or other gaseous media from a temperature above its transformation range. The term should be re- stricted...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.9781627082617
EISBN: 978-1-62708-261-7
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.t52310027
EISBN: 978-1-62708-286-0
..., it cannot be assumed that this relationship is true for other environments, although other empirical relationships exist or can be generated. Because the influence of alloying element varies with environment, we need to discuss some of the more commonly encountered severe environments. Corrosion in Acids...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 30 September 2023
DOI: 10.31399/asm.tb.stmflw.t59390325
EISBN: 978-1-62708-459-8
... and ostensibly simple problem of the axial upsetting of a cylinder, and then these principles will be applied to other processes. 11.1 Open-die Forging Open-die forging involves large workpiece strains and simple tooling such as flat platens, punches or saddles. Cogging is the process of reducing...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2001
DOI: 10.31399/asm.tb.aub.9781627082976
EISBN: 978-1-62708-297-6
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.aacppa.t51140069
EISBN: 978-1-62708-335-5
... alloys. It is clear that the damping characteristics of casting alloys in terms of the log decrement of decay from these tests are in the same broad range as those of the wrought alloys. Data for aluminum wrought alloys with cladding are included in the figure to indicate that 1xx.0 castings and others...