1-15 of 15 Search Results for

(Other, general, or unspecified) fracture

Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Series: ASM Technical Books
Publisher: ASM International
Published: 01 September 2008
DOI: 10.31399/asm.tb.fahtsc.t51130087
EISBN: 978-1-62708-284-6
.... The classical organization for types of damage (failures) is as follows: deformation, fracture, wear, corrosion or other environmental damage, and multiple or complex damage. The chapter also provides some examples of lack of conformance to specification that may at first look like the heat treater did...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2001
DOI: 10.31399/asm.tb.secwr.t68350043
EISBN: 978-1-62708-315-7
... are forced to move relative to each other. It is closely associated with any wear mechanisms that may be operating and with any lubricant and/or surface films that may be present, as well as the surface topographies. The heat generated as a result of the dissipation of frictional interaction may affect...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540169
EISBN: 978-1-62708-309-6
... testing of cracked plates has shown that, in general, fracture strengths are significantly below the net section yield limit (see Fig. 4.2 ). In other words, the remaining cross-sectional area of the cracked plate could not support the applied load as was assumed. Clearly, conventional stress analysis...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.t53060429
EISBN: 978-1-62708-261-7
...). A generic term denoting a air-hardening steel. A steel containing suffi- treatment consisting of heating to and holding cient carbon and other alloying elements to harden fully during cooling in air or other gaseous media from a temperature above its transformation range. The term should be re- stricted...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 January 2017
DOI: 10.31399/asm.tb.sccmpe2.t55090419
EISBN: 978-1-62708-266-2
... in a stress state of sufficient magnitude to induce fracture. Analysis of SCC service failures is quite involved and requires prescribed and thorough examination procedures. Appropriate methodologies for evaluating such service failures are the subject of this chapter. Other processes that cause failure...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 October 2011
DOI: 10.31399/asm.tb.mnm2.9781627082617
EISBN: 978-1-62708-261-7
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2004
DOI: 10.31399/asm.tb.aacppa.t51140069
EISBN: 978-1-62708-335-5
... alloys. It is clear that the damping characteristics of casting alloys in terms of the log decrement of decay from these tests are in the same broad range as those of the wrought alloys. Data for aluminum wrought alloys with cladding are included in the figure to indicate that 1xx.0 castings and others...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.t60490329
EISBN: 978-1-62708-340-9
... failures in these reactors. In other types of reactors not involving hydrogen environments or involving much-lower-pressure hydrogen environments (e.g., catalytic-cracking and catalytic-reforming reactors), operating temperatures may be sufficiently high to warrant taking creep, creep-rupture, and creep...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.mmfi.t69540001
EISBN: 978-1-62708-309-6
... , γ zx = τ zx / G The elongations ( Eq 1.11a ) and the distortions ( Eq 1.12 ) are independent of each other. Hence the general case of strain, produced by three normal and three shearing components of stress, can be obtained by superposition. Addition of the three...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 May 2018
DOI: 10.31399/asm.tb.hma.t59250025
EISBN: 978-1-62708-287-7
... was contracted for by an established ironmaster named William Coleman with his son-in-law Tom Carnegie and several other local businessmen. It was located on a tract of land known as Braddock’s Field, where General Braddock had been defeated during the French and Indian War. Andrew Carnegie joined them later...
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2008
DOI: 10.31399/asm.tb.ssde.t52310027
EISBN: 978-1-62708-286-0
..., it cannot be assumed that this relationship is true for other environments, although other empirical relationships exist or can be generated. Because the influence of alloying element varies with environment, we need to discuss some of the more commonly encountered severe environments. Corrosion in Acids...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 1989
DOI: 10.31399/asm.tb.dmlahtc.9781627083409
EISBN: 978-1-62708-340-9
Book Chapter

Series: ASM Technical Books
Publisher: ASM International
Published: 01 March 2006
DOI: 10.31399/asm.tb.fdsm.t69870105
EISBN: 978-1-62708-344-7
... it is but a generalization of the Rankine hypothesis and does not include a shear component for crack initiation. In this chapter, we later describe the method we favor for general treatment of multiaxial fatigue. However, before we do so it is appropriate to mention other methodologies that have been proposed in recent...
Series: ASM Technical Books
Publisher: ASM International
Published: 01 December 2001
DOI: 10.31399/asm.tb.aub.9781627082976
EISBN: 978-1-62708-297-6
Series: ASM Technical Books
Publisher: ASM International
Published: 01 August 2005
DOI: 10.31399/asm.tb.pb.t51230105
EISBN: 978-1-62708-351-5
... and other surface contamination up to the point where the brazing alloy flows over them. From this point of view, molten salt dip brazing is a superior process. Additional means are therefore necessary to encourage wetting and spreading of molten filler metals during fluxless brazing. In general...