The existence of austenite and ferrite, along with carbon alloying, is fundamental in the heat treatment of steel. In view of the importance of structure and its formation to heat treatment, this chapter describes the various microstructures that form in steels, the various factors that determine the formation of microstructures during heat treatment processing of steel, and some of the characteristic properties of each of the microstructures. The discussion also covers the constitution of iron during heat treatment and the phases of heat-treated steel with elaborated information on iron phase transformation, hysteresis in heating and cooling, ferrite and austenite as two crystal structures of solid iron, and the diffusion coefficient of carbon.

This chapter describes the phases and constituents present in iron-carbon steels in near-equilibrium conditions. It explains how to use phase diagrams to predict and manage the development of ferrite, austenite, cementite, and pearlite through controlled cooling. It discusses the transformations, grain structure, and properties associated with each phase and identifies the primary stabilizing elements. It includes several micrographs revealing various microstructural features and describes the processing route by which they were achieved. It explains how to estimate the volume fraction of iron-carbon phases in equilibrium and how to determine the amount of each phase that must be present to reach a desired composition. The chapter also discusses the phases associated with hypo- and hyper-eutectoid steels and presents more than a dozen micrographs, identifying important structural features along with cooling conditions and sample preparation procedures.

This chapter describes the iron-carbon phase diagram, its modification by alloying elements, and the effect of carbon on the chemistry and crystallography of austenite, ferrite, and cementite found in Fe-C alloys and steels. It also lays the groundwork for understanding important metallurgical concepts, including solubility, critical temperature, dislocation defects, slip, and diffusion, and how they affect the microstructure, properties, and behaviors of steel.

The microstructure of carbon steel is largely determined by the transformation of austenite to ferrite, cementite, and pearlite. This chapter focuses on the microstructures produced by diffusion-controlled transformations that occur at relatively low cooling rates. It describes the conditions that promote such transformations and, in turn, how they affect the structure of various phases and the rate at which they form. The chapter also discusses the concepts of transformation kinetics, minimum free energy, and nucleation and growth, and provides information on alloying, interphase precipitation, and various types of transformations.

The properties of cast iron are determined primarily by the form of carbon they contain, which in turn, is controlled by modifying compositions and cooling rates during casting. Certain alloys (such as Si, Al, Ni, Co, and Cu) promote graphite formation, while others (such as S, V, Cr, Sn, Mo, and Mn) promote the formation of cementite. This chapter examines the relative potencies of these alloys and their effect on microstructure. It covers the five most common commercial cast irons, including white, gray, ductile, malleable, and compacted graphite, describing their compositional ranges, distinguishing features, advantages, limitations, and applications.

This appendix includes two annotated iron-carbon (Fe-C) phase diagrams. One is a poster-size diagram showing iron-carbon phases up to 7 wt% C along with representative microstructures. The other diagram is close-up view showing the phases that occur from 0 to 1.2 wt% C. It also includes labels identifying the microconstituents that form in plain carbon steels under rapid quenching conditions.

This chapter examines the microstructure and properties of annealed and normalized steels containing more than 0.25% carbon. It shows, using detailed micrographs, how incrementally higher levels of carbon affect the structure and distribution of pearlite and how it intermingles with proeutectoid ferrite and cementite. It explains how ferrite and pearlite respond to deformation and how related features such as slip lines, dislocations, shear bands, and kinking can be detected as well as what they reveal. It also describes the structure of patented wires, cast steels, and sintered steels and the morphology of manganese sulfide inclusions in castings.

A spheroidized structure, which consists of spherically shaped cementite in a matrix of ferrite, is often desired in the production of steel, whether to improve properties, such as machinability and ductility, or accommodate subsequent hardening treatments. This chapter discusses the spheroidization of normalized and annealed steels by heating at subcritical temperatures. It explains how lamellar pearlite and proeutectoid cementite transform when heated and how deformation prior to heating affects both the mechanism and kinetics of spheroidization. It also explains how austenitizing contributes to the production of spheroidal transformation products and why secondary graphitization sometimes occurs.

This chapter discusses the isothermal transformation of austenite to pearlite, bainite, martensite, proeutectoid ferrite, and proeutectoid cementite. It describes the transformation mechanisms in eutectoid, hypoeutectoid, and hypereutectoid steels, the factors that influence nucleation and growth, and the characteristic features of the various microstructures. It also describes the transformation of austenite during continuous cooling.