This article introduces the wafer-level fault localization failure analysis (FA) process flow for an accelerated yield ramp-up of integrated circuits. It discusses the primary design considerations of a fault localization system with an emphasis on complex tester-based applications. The article presents examples that demonstrate the benefits of the enhanced wafer-level FA process. It also introduces the setup of the wafer-level fault localization system. The application of the wafer-level FA process on a 22 nm technology device failing memory test is studied and some common design limitations and their implications are discussed. The article presents a case study and finally introduces a different value-add application flow capitalizing on the wafer-level fault localization system.

As semiconductor feature sizes have shrunk, the technology needed to encapsulate modern integrated circuits has expanded. Due to the various industry changes, package failure analyses are becoming much more challenging; a systematic approach is therefore critical. This article proposes a package failure analysis flow for analyzing open and short failures. The flow begins with a review of data on how the device failed and how it was processed. Next, non-destructive techniques are performed to document the condition of the as-received units. The techniques discussed are external optical inspection, X-ray inspection, scanning acoustic microscopy, infrared (IR) microscopy, and electrical verification. The article discusses various fault isolation techniques to tackle the wide array of failure signatures, namely IR lock-in thermography, magnetic current imaging, time domain reflectometry, and electro-optical terahertz pulse reflectometry. The final step is the step-by-step inspection and deprocessing stage that begins once the defect has been imaged.

Since the introduction of chip scale packages (CSPs) in the early 90s, they have continuously increased their market share due to their advantages of small form factor, cost effectiveness and PCB optimization. The reduced package size brings challenges in performing failure analysis. This article provides an overview of CSPs and their classification as well as their advantages and applications, and reveals some of the challenges in performing failure analysis on CSPs, particularly for CSPs in special package configurations such as stacked die multi-chip-packages (MCPs) and wafer level CSPs (WLCSPs). The discussion covers special requirements of CSPs such as precision decapsulation for fine ball grid array packages, accessing the failing die for MCP packages, and careful handling for WLCSP. Solutions and best practices are shared on how to overcome these challenges. The article also presents a few case studies to demonstrate how failure analysis work on CSPs can be successfully completed.

The management of a failure analysis (FA) laboratory requires a broad range of activities to optimize the efficiency of the operation. The purpose of this article is to stimulate readers to consider the various aspects of FA laboratory operations and their respective business management requirements. The various aspects include: staffing, laboratory organization, lab design and operations, strategic development, financial management, and metrics and measurements. References for further reading and examples of resource materials are also included.

Moore's Law has driven many degree circuit features below the resolving capability of optical microscopy. Yet the optical microscope remains a valuable tool in failure analysis. This article describes the physics governing resolution and useful techniques for extracting the small details. It begins with the basic microscope column and construction. The article discusses microscope adjustments, brightfield and darkfield illumination, and microscope concepts important to liquid crystal techniques. It also discusses solid immersion lenses, infrared and ultraviolet microscopy and concludes with laser microscopy techniques such as thermal induced voltage alteration and external induced voltage alteration.

X-ray imaging systems have long played a critical role in failure analysis laboratories. This article begins by listing several favorable traits that make X-rays uniquely well suited for non-destructive evaluation and testing. It then provides information on X-ray equipment and X-ray microscopy and its application in failure analysis of integrated circuit (IC) packaging and IC boards. The final section is devoted to the discussion on nanoscale 3D X-ray microscopy and its applications.

The scanning acoustic microscope (SAM) is an important tool for development of improved molded and flip chip packages. The SAM used for integrated circuit inspection is a hybrid instrument with characteristics of both the Stanford SAM and the C-scan recorder. This chapter presents the historical development of SAM for integrated circuit package inspection, SAM theory, and analysis considerations. Case studies are presented to illustrate the practical applications of SAM. Other non-destructive imaging tools are briefly discussed, as well as SAM challenges and methods including spectral signature analysis and GHz-SAM.

In this overview of diagnosis of scan logic and diagnosis driven failure analysis, the authors explore the world of diagnosis of digital semiconductors devices. After shortly outlining the technology behind diagnosis, the main part of this article describes key improvements to the basic diagnosis tools, discussing their merits for the failure analysis engineer. The article also describes the various requirements and other considerations that typically need to be taken into account to set up a full working scan diagnosis system. It summarizes the principles of design with embedded compression technologies. Finally, several successful industrial applications of diagnosis are presented.

Magnetic field imaging (MFI), generally understood as mapping the magnetic field of a region or object of interest using magnetic sensors, has been used for fault isolation (FI) in microelectronic circuit failure analysis for almost two decades. Developments in 3D magnetic field analysis have proven the validity of using MFI for 3D FI and 3D current mapping. This article briefly discusses the fundamentals of the technique, paying special attention to critical capabilities like sensitivity and resolution, limitations of the standard technique, sensor requirements and, in particular, the solution to the 3D problem, along with examples of its application to real failures in devices.

Time-domain based characterization methods, mainly time-domain reflectometry (TDR) and time-domain transmissometry (TDT), have been used to locate faults in twisted cables, telegraph lines, and connectors in the electrical and telecommunication industry. This article provides a brief review of conventional TDR and its application limitations to advanced packages in semiconductor industry. The article introduces electro optical terahertz pulse reflectometry (EOTPR) and discusses how its improvements of using high frequency impulse signal addressed application challenges and quickly made it a well-adopted tool in the industry. The third part of this article introduces a new method which combines impulse signal and the TDT concept, and discusses a combo TDR and TDT method. Cases studies and application notes are shared and discussed for each technique. Application benefits and limitations of these techniques (TDR, EOTPR, and combo TDR/TDT) are summarized and compared.

Photon emission (PE) is one of the major optical techniques for contactless isolation of functional faults in integrated circuits (ICs) in full electrical operation. This article describes the fundamental mechanisms of PE in silicon based ICs. It presents the opportunities of contactless characterization for the most important electronic device, the MOS - Field Effect Transistor, the heart of ICs and their basic digital element, the CMOS inverter. The article discusses the specification and selection of detectors for proper PE applications. The main topics are image resolution, sensitivity, and spectral range of the detectors. The article also discusses the value and application of spectral information in the PE signal. It describes state of the art IC technologies. Finally, the article discusses the applications of PE in ICs and also I/O devices, integrated bipolar transistors in BiCMOS technologies, and parasitic bipolar effects like latch up.

This article reviews the basic physics behind active photon injection for local photocurrent generation in silicon and thermal laser stimulation along with standard scanning optical microscopy failure analysis tools. The discussion includes several models for understanding the local thermal effects on metallic lines, junctions, and complete devices. The article also provides a description and case study examples of multiple photocurrent and thermal injection techniques. The photocurrent examples are based on Optical Beam-Induced Current and Light-Induced Voltage Alteration. The thermal stimulus examples are Optical Beam-Induced Resistance Change/Thermally-Induced Voltage Alteration and Seebeck Effect Imaging. Lastly, the article discusses the application of solid immersion lenses to improve spatial resolution.

Many defects generate excessive heat during operation; this is due to the power dissipation associated with the excess current flow at the defect site. There are several thermal detection techniques for failure analysis and this article focuses on infrared thermography with lock-in detection, which detects an object's temperature from its infrared emission based on blackbody radiation physics. The basic principles and the interpretation of the results are reviewed. Some typical results and a series of examples illustrating the application of this technique are also shown. Brief sections are devoted to the discussion on liquid-crystal imaging and fluorescent microthermal imaging technique for thermal detection.

This chapter describes three approaches for 3D hot-spot localization of thermally active defects by lock-in thermography (LIT). In the first section, phase-shift analysis for analyzing stacked die packages is performed. The second example employs defocusing sequences for the localization of resistive electrical shorts in 3D architectures, and the third operates in cross sectional LIT mode to investigate defects in the insulation liner of Through Silicon Vias. All three approaches allow for a precise localization of thermally active defects in all three spatial dimensions to guide subsequent high-resolution physical analyses.

Diagnosing the root cause of a failure is particularly challenging if the symptom of the failure is not consistently observable. This article focuses on Laser Assisted Device Alteration/Soft Defect Localization (LADA/SDL), a global fault isolation technique, for detecting such failures. The discussion begins with a section describing the three steps in LADA/SDL analysis setup: create the test loop with the fail flag and loop trigger, select the laser dwell time, and select the shmoo bias point. An overview of LADA/SDL workflow is then presented followed by a brief section on time-resolved LADA. The closing pages of the article consider in detail SDL laser interaction physics and LADA laser interaction physics.

Laser Voltage Probing (LVP) is a key enabling technology that has matured into a well-established and essential analytical optical technique that is crucial for observing and evaluating internal circuit activity. This article begins by providing an overview on LVP history and LVP theory, providing information on electro-optical effects and free-carrier effects. It then focuses on commercially available continuous wave LVP systems. Alternative optoelectronic imaging and probing technologies for fault isolation, namely frequency mapping and laser voltage tracing, are also discussed. The subsequent section provides information on the use of Visible Laser Probing. The article closes with some common LVP observations/considerations and limitations and future work concerning LVP.

Over the revolutionary era of semiconductor technology, Computer-Aided Design Navigation (CADNav) tools have played an increasingly critical role in silicon debug and failure analysis (FA) in efforts to improve manufacturing yield while reducing time-to-market for integrated circuit (IC) products. This article encompasses the key principles of CADNav for various aspects of semiconductor FA and its importance for improved yield and profitability. An overview of the required input data and formats are described for both IC and package devices, along with key considerations and best practices recommended for fast fault localization, accurate root cause analysis, FA equipment utilization, efficient cross-team collaboration, and database management. Challenges with an FA lab ecosystem are addressed by providing an integrated database and software platform that enable design layout and schematic analysis in the FA lab for quick and accurate navigation and cross-tool collaboration.

This chapter provides a comprehensive overview over all phenomena related to Voltage Contrast (VC) mechanisms in SEM and FIB. The multiple advantages, possibilities, and limits of active and passive VC failure localization are systemized and discussed. The knowledge of all facts influencing the VC generation (capacitance, leakage, doping, and circuitry) is very helpful for successful failure localization.

With the commercialization of heavier and lighter ion beams, adoption of focused ion beam (FIB) use for analysis of challenging regions of interest (ROI) has grown. In this chapter, the authors focus on highlighting commercially available and complementary FIB technologies and their implementation challenges and application trends.