A modified stainless steel coating, named as M-SUS here, was prepared by the air plasma spray process (APS) and the high velocity flame spray process (HVOF) and compared with a conventional stainless steel (JIS: SUS316L). Anodic polarization tests using NaCl, HCl solutions, neutral salt spray test, and exposure test in actual tank for HCl storage were employed for the evaluation of corrosion resistance. Structure of the coatings was investigated by use of optical microscope, scanning electron microscope, electron probe micro-analyzer, and transmission electron microscope. It was found that the coating M-SUS exhibited a remarkably superior corrosion resistance by all tests mentioned above, compared with the conventional ones. Although both of the coatings compose of gamma-austenite (γ-Fe) and delta-ferrite (δ-Fe) phases, the coating M-SUS reveals much less oxide with chromium and more delta-phase enriched with molybdenum. Another exposure test using a mixed acid of 25%HNO3 and 75%HCl yielded that the δ-Fe was not etched out but the γ-Fe vanished, that is, the δ-Fe of M-SUS has a strong anti-corrosion property. It is considered that the superior corrosion resistance of coating M-SUS is attributed to the extensive formation of anti-corrosive δ-Fe and inhibition of chromium depletion resulting from oxide formation.

Oxidation is a serious issue for thermally sprayed alloy coatings, especially in atmospheric plasma spray (APS) process, by which it is believed to be impossible to obtain alloy coatings with low oxide content. Oxidation behavior of Ni20Cr alloy and NiCrSiBC alloy in APS were compared by evaluating collected in-flight particles and sprayed coatings in our previous study. The results clearly show that the oxide content in the in-flight particles and coating of NiCrSiBC alloy was significantly lower than that of Ni20Cr alloy. In the present study, further study of the surface oxide layer of NiCrSiBC coating was carried out by TEM, which showed 10 nm thick oxygen enriched layer. The effects of particle temperature and velocity on the oxidation of the NiCrSiBC alloy were investigated. It was found that increasing particle temperature and velocity did not affect the oxidation of inflight particle of the NiCrSiBC alloy but significantly increased the oxidation after particle impacting substrate. The results are discussed in conjunction with effectiveness of preferential oxidation of Si, B, C and simultaneous vaporization of the formed oxides on suppressing in-flight oxidation and influence of a large amount of sub-particles produced upon impacting substrate on oxidation characteristics when increasing plasma power.

This study investigates the effect of alloying additions on the oxidation behavior of iron (Fe) and nickel-chromium (NiCr) powders during atmosphere plasma spraying. The chemical composition and phases of oxides in the particles as well as in the coatings are assessed for different powder mixtures and spraying parameters. The results show that oxygen content can be significantly reduced by adding silicon (Si) and boron (B) to iron powders and Si, B, and carbon (C) to NiCr. The preferential oxidation and subsequent vaporization of Si, B, and C from the surface of the sprayed particles are believed to play a major role in controlling oxidation in the APS process.

SUS316L coatings were sprayed by a high-velocity air fuel (HVAF) system to reduce oxidation and thereby improve the corrosion behavior of stainless coatings. The effects of powder feed rate and particle size on the microstructure, oxide amount and adhesion strength of the coatings were investigated. The corrosion resistance of the coatings was evaluated by conducting salt spray tests. The oxide amount in the coatings sprayed by the HVAF process is below 7 % and adhesion strength is below 34 MPa. In comparison with those of coatings sprayed by a high velocity oxygen fuel (HVOF) system, the oxide amount and adhesion strength are decreased because the particles heated below the melting point of the alloy and insufficient softened in HVAF process. The coatings deposited are original porous, and they become denser through the impinging effect caused by the following sprayed particles. With the increase of powder feed rate and particle size, there is a tendency of reduction in oxides, and an obvious decrease in adhesion strength. Corrosion resistance of the unsealed coatings is insufficient, and this becomes notable with increasing powder feed rate and particle size. The sealed HVAF coating sprayed with the largest particles shows the best corrosion resistance.

The microstructure of arc sprayed stainless steel 316L coatings appears mainly in bright white matrix, deteriorated layers (grey), and black pores under optical microscopy. The black pores and the chromium-depleted areas in the deteriorated layers are known as the factors for decreasing the ability of protecting substrate under corrosive environments. Results of experiments in this paper suggests, in the condition of this study besides the factors mentioned above, Fe-Cr oxides should be another factor of dominating the corrosion resistance in the coatings. It also describes that the quantity and the distributions of such oxides are great influence on the corrosion behaviors. In this study, two kinds of coatings were used, one with thick deteriorated layers and another with thin deteriorated layers, which were sprayed on mild steel substrate by air atomization and nitrogen atomization respectively. Salt spray test and salt-water dip test were carried out to investigate corrosion behavior in macro and micro view. An effect of sealing treatment on the performance of the coatings was also examined. Results of metallographic examination and image processing analysis are well supported by a detailed investigation of corrosion behaviors of individual phases.