Measurement of the particle temperature and velocity in detonation spraying is significantly complicated by the pulsed character of the process. In the present study, these parameters are measured for powders with strongly different nature and properties such as WC/Co, Inox and Ti. Experiments are performed using an original computer-controlled detonation spraying (CCDS) installation developed by the authors. The system is distinguished by the mode of powder feeding into the gun barrel which is pulsed in time and localized in space. Evolution of the particle-in-flight velocity and size is examined by an original CCD-camera-based diagnostic tool developed by the authors. A significant spatial separation of the particles along the detonation plume is observed during their acceleration: 15 μm fine particles overtake 45 μm coarse particles by more than 10 plume diameters. For this reason, distributed scanning over the plume length is applied in order to obtain adequate results. A previously developed mathematical model of the process is experimentally validated. Calculations are found to be in a qualitative agreement with the experimental results. As far as particle-in-flight velocity is concerned, the agreement is even quantitative.

Cold and detonation spraying methods are based on the interaction of high-velocity particles with substrate. High quality coatings from various powder materials can be deposited. In both processes, the substrate experiences insignificant thermal effect. Thermally sensitive powder can be sprayed with no oxidation and decomposition. The initial powder microstructure and even nanostructure can be preserved under properly selected spraying conditions. This study is based on a comparative analysis of the mechanical, electrical, and heat transfer properties of a series of coatings deposited by cold and detonation spraying technologies. The coatings are produced from copper and aluminum powders using a commercial Cold Spray equipment CGT-4000 and an original computer-controlled detonation spraying (CCDS) installation developed by the authors. The coating microhardness, density, electrical and heat conductivity, adhesion, cohesion, etc. are measured and compared. Particular advantages and drawbacks of both spraying methods are discussed.

Properties of detonation coatings from composite powders based on carbides are studied. The main focus is on tungsten carbide. Powders with carbide inclusions of different size ranging from a ten of microns down to the submicron level are analysed. Composites with cobalt binder content from 12 to 30 % and composite binders with chromium and nickel additions are studied. A comparative analysis between composites with chrome carbide and the complex titan-chrome carbide produced by self-propagating high–temperature synthesis is done. Powders are sprayed with a new generation detonation gun “Dragon” designed at Lavrentyev Institute of Hydrodynamics SB RAS. The apparatus is characterized by a high-precision gas supply system and a dosed localized powder feeding system. Computer control provides a flexible programmed readjustment of the detonation gases energy impact on powder particles thus allowing selecting the optimal for each material spraying parameters to form high-quality cermet composite coatings. Physical properties and functional performance of the obtained coatings are studied. Microstructure and microhardness analyses, adhesion/cohesion, abrasion, erosion and friction wear tests of the coatings are performed. It is found that the studied materials do not exhibit overwhelming advantages in performance compared with one another. Fore example, though composites with a great content of binder has a relatively low wear resistance, they exhibits the highest adhesion to the substrate while composites with titan-chrome carbide compared to tungsten carbide-based composites have higher dry friction and lower lubricated friction.

Metallization of plastics by thermal spraying is studied. The possibility to obtain high adhesion of metal particles to the surface of a wide range of plastic materials is shown. Powders are sprayed with a new generation detonation gun “Dragon” designed at Lavrentyev Institute of Hydrodynamics SB RAS. The apparatus is characterized by a high-precision gas supply system and a dosed localized powder feeding system. Computer control provides a flexible programmed readjustment of the detonation gases energy impact on powder particles which is a key factor in precision control of spraying parameters for low-melting point powder materials. It is found that under certain spraying conditions molten particles of a low-melting point material not only do not provoke erosion of plastic material at their high velocity impact on the substrate but strong-bond fusion, sufficient to further form a thick coating, occurs. Aluminium, zinc and tin powders are sprayed on substrates from fibreglass, polyester, fluoroplastic and some other plastics. Load capacity of the obtained coatings reaches 100 kg/cm 2 . It is shown that on top of a thin layer from a low-melting point powder material high-melting point metals and even ceramics can be deposited.