Boundary layers on surfaces will change from laminar to turbulent flow after a critical length. Due to the differing heat transfer coefficients of laminar and turbulent flow, the point of transition can be detected by heating the surface and measuring surface temperature by thermographic imaging. Locating the transition point is crucial for the aerodynamic optimization of components. In this study, fiber reinforced polymer composites (FRPCs) were chosen as the test substrate. Experiments were conducted using the flame spray process and NiCrAlY coatings. Multilayered coatings consisting of an aluminum bond coat, a layer of alumina as electrical insulation, and a heating layer of titania were fabricated by atmospheric plasma spraying. Free-flight tests were conducted with a functionalized winglet in order to assess the ability of thermally-sprayed heating elements to detect the location of transition of the flow regime. The results showed that the thermally-sprayed elements heat surfaces uniformly, with sufficient radiation losses for thermographic imaging. It was also shown that the change in temperature at the point of transition was readily observable using thermography.

Dense sintered technical ceramics demand special surface preparation in order to be coated by thermal spraying. Sandblasting results in the damage of the interface region and leads to bonding defects. On the contrary, by varying the laser conditions, different laser structured surfaces were generated, which at Rz roughness values in the range of 40 μm, allowed to achieve thick and well bonding coatings. Therefore, laser ablation is proved to be the best method for surface preparation of ceramic substrates. In the case of porous ceramics (including pre-sintered ceramics) substrate preparation can be omitted, depending on their porosity level. Ceramics with porosity content up to 60 % can be coated by APS, whereas HVOF can be used on ceramics with porosity up to 30 %. On ready-to-get-coated pre-sintered ceramic parts (without substrate preparation), followed by co-firing of the substrates and coatings, the development of new ceramic components is possible.

The work presented in this paper addresses some of the challenges of manufacturing thermoelectric (TE) generators by thermal spraying. One of the main obstacles is achieving good coat-on-coat bonding between different types of materials. The coatings must also be mechanically stable and optimized for their respective function. At least four types of materials are required, including electrical insulators, conductors, and thermoelectrically active p- and n-type semiconductors. Four ceramic and three metal feedstock powers were deposited by APS, HVOF, and HVAF spraying using special masking systems, substrate pretreatments, and layer thickness monitoring. After process optimization for each material, multilayer TE generator modules were successfully produced.

This work assesses the challenges of preparing dense technical ceramic substrates for thermal spraying and evaluates the capabilities of laser ablation in comparison with sandblasting. Sintered Si3N4 and AlN substrates were prepared by both methods and surface roughness was measured before and after treatment. Alumina coatings were deposited by suspension-HVOF and atmospheric plasma spraying, and coating cross-sections were analyzed by optical microscopy and SEM. Sandblasting had little or no effect on surface roughness and cracks were observed in coating cross-sections at the near-surface region of the substrate. Laser ablation, on the other hand, significantly increased surface roughness for both ceramics, producing hole patterns that are shown to vary with laser power and pulse timing. In the case of plasma spraying, the best coatings were achieved when the holes in the substrate were less than 100 µm in depth. With suspension sprayed coatings, the best results were obtained on substrates with deeper (> 100 µm) holes.

Different feedstock powder compositions of the alumina-chromia system were deposited on steel substrates by various methods, including conventional plasma spraying, three-anode plasma spraying, and HVOF. The powders used for plasma spraying had particle sizes of -38+10 µm and for HVOF spraying -25+5 µm and -25+10 µm. The coatings were evaluated by their microstructure, phase composition, and corrosion, wear, and electrical properties. The study shows that wear properties depend strongly on the spray process and that coatings obtained by HVOF spraying have dense structures and excellent wear behavior. Coatings produced by the three-anode plasma process, despite their higher porosity, were found to be harder than conventional plasma coatings and can be sprayed with higher feed rates. The coating properties do not appear to have a linear dependence on chromia content.

In this work, completely ceramic heating elements have been developed by the combination of conductive and insulating thermally sprayed oxide coatings. These heating elements with a total thickness of less than 1 mm have been directly applied on metallic substrates. APS- and HVOF-sprayed Al 2 O 3 and spinel (MgAl 2 O 4 ) coatings were employed for insulation. A comparative analysis of the insulating properties (dielectric strength, electrical resistivity) of these coatings is presented. The HVOF-sprayed spinel coatings show better dielectric breakdown strength and higher electrical resistance stability. TiO x , TiO 2 -10%Cr 2 O 3 and TiO 2 -20%Cr 2 O 3 powders have been used to prepare the electrical conductive coatings. The thermal and oxidation stabilities at high temperature, as well the electrical properties have been investigated. Addition of Cr 2 O 3 reduced the oxidation rate of titanium oxide and increased the operational temperature of the heating coating. A ceramic heater consisting of spinel coating as insulator and TiO 2 - 20Cr 2 O 3 as conductor was sprayed on a metallic roller and the electrical stability during the long-term (300h) thermo-cycling (from RT to 300°C) was successfully tested.

In this paper the characteristics (microstructure, phase compositions) and electrical insulating properties of thermally sprayed alumina coatings produced by suspension-HVOF (S-HVOF) process and conventional HVOF spray method are compared. The electrical resistance (electrical resistivity) and dielectric strength were investigated using DC-electrical resistance measurements, electrochemical impedance spectroscopy (EIS) and dielectric breakdown test. The electrical resistance was determined at room temperature at different relative air humidity (RH) levels, from 6% RH up to 97% RH. Differences in the electrical insulating properties due to the different coating characteristics are discussed. The suspension-sprayed Al 2 O 3 coatings showed better electrical resistance stability at high humidity levels (> 75% RH), which could be explained by a specific microstructure and retention of a higher content of α-Al 2 O 3 . Nonetheless, the values of dielectric breakdown voltage and dielectric strength recorded for suspension sprayed coatings were lower than those of HVOF coatings.

In the present work, APS and HVOF processes have been used to prepare alumina (Al 2 O 3 ) and magnesium aluminate spinel (MgAl 2 O 4 ) coatings designed for electrical insulating applications. The microstructures and the phase compositions of the sprayed coatings were evaluated by microscopic and XRD analysis. The electrical characteristics electrical resistance, electrical resistivity and dielectric breakdown strength were investigated using different methods: direct current (DC) measurements, electrochemical impedance spectroscopy (EIS) and dielectric breakdown testing. The electrical resistance was measured at room temperature at different humidity levels. Differences in the insulating properties due to the different natures of the coating materials, microstructures and the measurement methods used for electrical characterisation are discussed.